Flir Forge Bruksanvisning
Flir
ej kategoriserat
Forge
Läs gratis den bruksanvisning för Flir Forge (2 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 2 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 1.5 recensioner. Har du en fråga om Flir Forge eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
GETTING
GETTING
GETTING
GETTINGGETTING
STARTED
STARTED
STARTED
STARTEDSTARTED
FORGE®
GigE Vision
Will
Will
Will
WillWill your
your
your
youryour system
system
system
systemsystem support
support
support
supportsupport the
the
the
thethe camera?
camera?
camera?
camera?camera?
Recommended System Configuration:
n
OS—Windowsor Linux (32- or 64-bit)
n
CPU— Intel i7 or greater
n
RAM—8 GB dual channel
n
Ports—GigE network adapter with 5G Full Duplex support
n
Software—Microsoft Visual Studio 2015 (to run and compile example code)
Do
Do
Do
DoDo you
you
you
youyou have
have
have
havehave a
a
a
aa downloads
downloads
downloads
downloadsdownloads account?
account?
account?
account?account?
A downloads account is required to download software and firmware.
1. Go to .www.flir.com/account
2. Enter your email address and click Continue.
3. Complete the Create an account form and click Continue.
4. You will receive an email with a link to activate your account.
5. Once activated, you can login using the credentials you've created.
The has many links to help you operate your cameraForge resources page
effectively, including:
n
Spinnaker
®
SDKsoftware, including drivers (login required)
n
Firmware updates and release notes (login required)
n
Dimensional drawings and CADmodels
n
Documentation
Do
Do
Do
DoDo you
you
you
youyou have
have
have
havehave all
all
all
allall the
the
the
thethe parts
parts
parts
partsparts you
you
you
youyou need?
need?
need?
need?need?
To install your camera you need the following components:
n
Ethernet cable
n
Powered Ethernet switch or Ethernet power injector (if using PoE)
n
GPIOcable
n
Lens
n
Tripod adapter (optional)
n
Interface card
Teledyne FLIR sells a number of the additional parts required for installation. To
purchase, visit the .Accessories page
Camera
Camera
Camera
CameraCamera Care
Care
Care
CareCare
To clean the imaging surface of your camera, follow the steps outlined in Cleaning
the imaging surface of your camera.
Extended exposure to bright sunlight, rain, dusty environments, etc. may cause
problems with the electronics and optics of the system.
Avoid excessive shaking, dropping, or mishandling of the device.
Warning! Avoid electrostatic charging.
Installing
Installing
Installing
InstallingInstalling your
your
your
youryour Interface
Interface
Interface
InterfaceInterface Card
Card
Card
CardCard and
and
and
andand Software
Software
Software
SoftwareSoftware
1. Install your Interface Card
Ensure the card is installed per the
manufacturer's instructions.
Connect the internal IDE or SATApower
connector on the card to the computer power
supply.
Alternatively, use your PC's built- in host
controller, if equipped.
Open the Windows Device Manager. Ensure the card is properly installed. Ethernet
cards appear under . An exclamation point (!) next to the cardNetwork Adapters
indicates the driver has not yet been installed.
Configure the network adapter to use 5G Full Duplex.
a. Update the driver to the latest to access the 5GFull Duplex option.
b. In Windows go to Control Panel\Network and Internet\Network Connections,
right-click on your network adapter and select .Properties
c. Click .Configure
d. On the Advanced tab, from the Property box select and fromSpeed &Duplex
the Value drop-down select .5Gbps Full Duplex
e. Click .OK
On the Advanced tab, if not already enabled, set the Jumbo Packet to 9014 Bytes.
2. Install the Spinnaker® SDK Software
Note: For existing users who already have Spinnaker installed, we recommend
ensuring you have the latest version for optimal performance of your camera. If
you do not need to install Spinnaker, use SpinView to install and enable drivers
for your card. Forge requires Spinnaker version 3.1 or later.
a. Go to the page.Spinnaker SDK
b. Click the Download button. You are prompted to login, if not already.
c. Select your operating system. Depending on your selection there may be other
versions to select.
d. After download is complete, open the file to start the Spinnaker setup wizard.
e. Follow the steps in each setup dialog.
3. Optimize the settings of your Ethernet card
a. In , right click on the NetworkStart->All Programs-> Spinnaker SDK->SpinView
Adapter and select Adapter Configuration. The Adapter Config Utility lists your
network adapters and allows you to access the following:
n
Adapter IP address
n
Subnet mask
n
Default gateway
n
Receive buffers
n
Transmit buffers
n
Jumbo packets
n
RSS
n
Media optimization
n
CPU affinity
Note: See How to Optimize GigENetwork Adapter Settings for more information
on configuring for best performance.
5/19/2023
Names and marks appearing on the products herein are either registered
trademarks or trademarks of FLIR Integrated Imaging Solutions Inc. and/or its
subsidiaries.
© 2015-2023 FLIR Integrated Imaging Solutions Inc. All rights reserved.
Using
Using
Using
UsingUsing the
the
the
thethe Spinnaker
Spinnaker
Spinnaker
SpinnakerSpinnaker
®
®
®
®®
SDK
SDK
SDK
SDKSDK
You can monitor or control features of the camera through Spinnaker API
examples provided in the Spinnaker SDK, or through the SpinView camera
evaluation application. A is included inProgrammer's Guide and API Reference
the installation.
Installing
Installing
Installing
InstallingInstalling your
your
your
youryour Forge
Forge
Forge
ForgeForge 5GigE
5GigE
5GigE
5GigE5GigE
1. Attach a Lens
Unscrew the dust cap from the lens holder to install a lens.
2. Connect the interface Card and Cable to the Camera
Plug the interface cable into the host controller card and the camera. The
cable jack screws can be used for a secure connection. If using PoE, connect a
powered Ethernet switch or Ethernet power injector in between the card and
the camera.
When the camera is first connected, the operating system automatically installs
the camera driver. Camera drivers are available with the Spinnaker SDK
installation.
3. Plug in the GPIO connector
GPIOis used for power, trigger, serial input output, and strobe.
4. Confirm Successful Installation
Run the SpinView application: Start->All Programs-> Spinnaker->SpinView
The SpinView application can be used to test the camera's image acquisition
capabilities and make changes to the camera's installation configuration.
5. Configure IPSettings if necessary
By default, a dynamic IPaddress is assigned to the camera according to the
DHCP protocol. If DHCP addressing fails, a link- local address is assigned. If
necessary, in SpinView change the IPaddress of the camera to be on the same
subnet as the NIC.
Status
Status
Status
StatusStatus Indicator
Indicator
Indicator
IndicatorIndicator LED
LED
LED
LEDLED
LED 5GigE
No Light
No power
or LED is in inactive state
or LED is in error status state with no error
Blinking Green (1 blink)
Link-Local Address (LLA)
Blinking Green (2 blinks)
DHCPIPAddress
Blinking Green (3 blinks)
Persistent IPAddress
Solid Green
Acquisition Started
Rapid Flashing Green
Firmware update in progress
Flashing Green and Red
General Error
Camera
Camera
Camera
CameraCamera Interface
Interface
Interface
InterfaceInterface
Ethernet
Ethernet
Ethernet
EthernetEthernet Connector
Connector
Connector
ConnectorConnector
The 8-pin RJ-45 Ethernet jack is equipped with two (2) M2 screwholes for secure
connection. Pin assignments conform to the Ethernet standard.
General
General
General
GeneralGeneral Purpose
Purpose
Purpose
PurposePurpose I/O
I/O
I/O
I/OI/O Connector
Connector
Connector
ConnectorConnector
The camera is equipped with a 6-pin GPIO connector on the back of the case.
Diagram Color
1
Pin Line Function Description
Green 1
2
3
V
EXT
External Input Voltage
(DC)
GPI Non-isolated Input
Black 2 0 OPTOIN Opto-isolated Input
Red 3
2
2
V
AUX
OUT Auxiliary Power Output
GPIO
3
Non-isolated Input/Output
White 4 1 OPTOOUT
3
Opto-isolated Output
Blue 5 N/A Opto GND Opto-isolated Ground
Brown 6 N/A GND Camera Power Ground
1—GPIO cable assembly wire colors
2—Dual function pin
3—Open drain output, requires pullup resistor
For
For
For
ForFor More
More
More
MoreMore Information
Information
Information
InformationInformation
Teledyne FLIR endeavors to provide the highest level of technical support
possible to you.
Support resources can be accessed through the .Forge resources page
Your camera's settings and capabilities—Technical Reference or Camera Reference
Spinnaker® SDK—API Reference / Programmer's Guide
Selecting a lens for your camera
Setting Up Multiple GigECameras
How to Optimize GigENetwork Adapter Settings
Using the Spinnaker Multicore GigE Optimizer
Using third-party applications from our software partners
Contacting
Contacting
Contacting
ContactingContacting Us
Us
Us
UsUs
For any questions, concerns or comments please contact us via the following
methods:
Email
General questions
Support Ticket
Technical support
Website
Find specifications, support articles, downloads on the
product page at Teledyne FLIRmachine vision
5/19/2023
Names and marks appearing on the products herein are either registered
trademarks or trademarks of FLIR Integrated Imaging Solutions Inc. and/or its
subsidiaries.
© 2015-2023 FLIR Integrated Imaging Solutions Inc. All rights reserved.
Produktspecifikationer
| Varumärke: | Flir |
| Kategori: | ej kategoriserat |
| Modell: | Forge |
Behöver du hjälp?
Om du behöver hjälp med Flir Forge ställ en fråga nedan och andra användare kommer att svara dig
ej kategoriserat Flir Manualer
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
14 Juli 2025
14 Juli 2025
ej kategoriserat Manualer
- Fuxtec
- Parasound
- Outwell
- Draper
- Arturia
- Cougar
- Heylo
- Metz Connect
- Chamberlain
- Peplink
- Lavor
- OmniMount
- Microchip
- Bernstein
- Hughes & Kettner
Nyaste ej kategoriserat Manualer
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025