Fluke SBP3 Bruksanvisning

Fluke Accu SBP3

Läs gratis den bruksanvisning för Fluke SBP3 (2 sidor) i kategorin Accu. Guiden har ansetts hjälpsam av 10 personer och har ett genomsnittsbetyg på 4.8 stjärnor baserat på 5.5 recensioner. Har du en fråga om Fluke SBP3 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Sida 1/2
FLK-TI-SBC3B
Charging Base/Power Supply with Adapters
Instruction Sheet
The Fluke FLK-TI-SBC3B Charging Base/Power Supply with Adapters charges the Fluke
FLK-TI-SBP3B Smart Battery Pack for Thermal Imagers. The FLK-TI-SBC3B consists of a
charging base, power supply, and power outlet adapters.
PN 4352179 May 2013
© 2013 Fluke Corporation. All rights reserved.
All product names are trademarks of their respective companies. Specications are subject to change without notice.
Safety Information
Use the FLK-TI-SBC3B only as specied in this instruction sheet or other Fluke
product-specic manual. See Table 1 for a list of symbols used on the FLK-TI-SBC3B.
A Warning identies hazardous conditions and procedures that are dangerous to the user.
A Caution identies conditions and procedures that may cause damage to the Product or
the equipment under test.
W Warning
To avoid injury:
Do not disassemble or short circuit the battery pack.
Do not expose the battery pack to temperatures above 50 °C (122 °F).
Do not incinerate or mutilate the battery pack.
Use only ac adapters approved by Fluke for the product to charge the battery or
power the product.
Table 1. Symbols
Symbol Description
P
Conforms to requirements of European Union and European Free Trade Association.
"
Imager connected to battery charger.
;
Conforms to relevant Australian standards.
)
Conforms to relevant Canadian and US standards
W
Important information. See manual.
~
This product complies with the WEEE Directive (2002/96/EC) marking requirements.
The afxed label indicates that you must not discard this electrical/electronic product in
domestic household waste. Product Category: With reference to the equipment types
in the WEEE Directive Annex I, this product is classed as category 9 “Monitoring and
Control Instrumentation” product. Do not dispose of this product as unsorted municipal
waste. Go to Fluke’s website for recycling information.
Charging the Battery
Before using the battery pack for the rst time, charge the battery in the two-bay charging
base for at least two and one-half hours. For complete charging instructions, see the
Thermal Imagers User Manual.
Specications
See Table 2 for the specications.
Table 2. Specications
Battery Charging
10-15 Vdc 2 A or charge battery pack in Imager with included ac
adapter rated: 100-240 Vac 50/60 Hz, 15 V 2 A.
Charging / Power LED
Status Charging LED Power LED
off no battery detected no dc power input
solid green charged dc power present
blinking green charging na
blinking red fault na
Dimensions 159.5 mm x 68.9 mm x 51.3 mm (6.28 in x 2.71 in x 2.02 in)
Operating Temperature -10 °C to 70 °C (-14 °F to 158 °F)
Storage Temperature -20 °C to 80 °C (-4 °F to 176 °F) without batteries
Humidity Range 10 % to 95 % non-condensing


Produktspecifikationer

Varumärke: Fluke
Kategori: Accu
Modell: SBP3

Behöver du hjälp?

Om du behöver hjälp med Fluke SBP3 ställ en fråga nedan och andra användare kommer att svara dig