Furuno FAPAR4502 Bruksanvisning
Läs gratis den bruksanvisning för Furuno FAPAR4502 (2 sidor) i kategorin Marin. Guiden har ansetts hjälpsam av 15 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 8 recensioner. Har du en fråga om Furuno FAPAR4502 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
Before you do it your way,
please try it our way
TELEFLEX CANADA
3831 NO.6 ROAD
RICHMOND, B.C.
CANADA V6V 1P6
FAX 604-270-7172
www.seastarsteering.com
© 2005 TELEFLEX CANADA LIMITED PARTNERSHIP
PRINTED IN CANADA
FORM NO. 269064 - 03/06 Rev C
ISO 10592
INSTALLATION INSTRUCTIONS
SUPPLEMENTAL
20
Autopilot Rudder Reference
SMART
STICK
I S O 9 0 0 1
MANUFACTURED BY
TELEFLEX CANADA LIMITED
PARTNERSHIP
H Y D R AU L I C
INSTALLATION INSTRUCTIONS
1Remove the nuts and washers
(item 1 & 2) from the steering
cylinder rod. Discard washers
(item 2) as they will not be used
in the SmartStick installation.
2Install brackets (item 3) onto the
ends of the cylinder support rod.
Re-install the nuts (item 1) and
torque to 33 in. lb. (3.82 Nm).
3Install the sensor (item 4) behind
the brackets as shown in figures
A and B.
4Mount the magnet (item 5) to the
center of the cylinder body with the
arrow pointed in the same direction
as the arrow on the sensor.
5Turn steering cylinder so that the
magnet arrow and the sensor decal
arrow are nearest each other.
6Without changing the position
along the length of the cylinder,
rotate the magnet on the cylinder
so that the arrows on the sensor
and magnet are as closely lined
up as possible.
7Tighten band clamp to 3 in. lb.
(0.35 Nm) to secure the magnet
in position.
Correct installation of the magnet
is important to the overall
operation of the autopilot.
Over tightening clamp may cause
magnet to break.
8Connect Rudder Reference to
autopilot as per autopilot instal-
lation instructions. Refer to Table
1 to ensure correct application
9Move the steering cylinder from
hard over to hard over to confirm
that the autopilot receives a
signal from the sensor at ALL
cylinder positions.
10
Install Strain relief (item 6).
Failure to install the strain relief
may result in irreparable damage
to the sensor.
NOTICE
NOTICE
NOTICE
TOOLS REQUIRED
5/8" Wrench 5/16" Wrench
11/32" Wrench 3/32" Allen Key
Torque Wrench
Produktspecifikationer
| Varumärke: | Furuno |
| Kategori: | Marin |
| Modell: | FAPAR4502 |
Behöver du hjälp?
Om du behöver hjälp med Furuno FAPAR4502 ställ en fråga nedan och andra användare kommer att svara dig
Marin Furuno Manualer
10 September 2024
10 September 2024
10 September 2024
10 September 2024
8 September 2024
6 September 2024
5 September 2024
2 September 2024
1 September 2024
1 September 2024
Marin Manualer
- Navman
- BandG
- Alphatron
- Polmar
- Efoy
- Silva
- AdvanSea
- Simrad
- Raymarine
- Nordwest-funk
- Klarfit
- Nasa
- SEAFARER
- Plastimo
- Icom
Nyaste Marin Manualer
10 Januari 2025
22 Oktober 2024
21 Oktober 2024
18 Oktober 2024
5 Oktober 2024
23 September 2024
21 September 2024
20 September 2024
18 September 2024
15 September 2024