Garde XL 181TSXL732 Bruksanvisning
Garde XL
skärmaskin
181TSXL732
Läs gratis den bruksanvisning för Garde XL 181TSXL732 (1 sidor) i kategorin skärmaskin. Guiden har ansetts hjälpsam av 5 personer och har ett genomsnittsbetyg på 4.2 stjärnor baserat på 3 recensioner. Har du en fråga om Garde XL 181TSXL732 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/1
QUICK START GUIDE
SERRATED BLADE TOMATO SLICERS
MODELS
181TSXL316 - 3/16" Slices
181TSXL732 - 7/32" Slices
181TSXL14 - 1/4" Slices
181TSXL38 - 3/8" Slices
SAFETY INSTRUCTIONS
CAUTION
Be careful when handling and operating the machine, as
the blades are very sharp. Always keep your hands away
from the blades.
PREPARATION
1. This unit comes fully assembled.
2. Place the unit on a sturdy work surface.
3. The guides for the pusher assembly located along the
sides of the cutting board need to be lubed regularly to
keep your slicer operating smoothly. Using a food grade
sanitary lube (such as 401PETROLGEL) will ensure you
get a clean slice every time.
OPERATION
1. Pull the handle toward you and place a tomato on the
slide board between the pusher plates and the blades.
2. Remove hands and ngers from the cutting area
and push the handle toward the blades with one
quick motion.
3. Remove the sliced tomato from the slide board
and repeat as necessary.
BLADE TENSION INSTRUCTIONS
1. Ensure that the blade holder assembly is rmly
mounted on the frame with the sharp side of the
blades toward the pusher assembly.
2. Be sure the hex head screws on the right side of the
blade holder are tight.
3. Tighten the hex head screws on the left end of the
blade holder until the blades “hum” when strummed
or plucked.
4. Check the blade tension each time the machine is used.
CLEANING
NOTE: Avoid using alkaline cleaners as they may dull the
nish and cause pitting.
1. Remove the thumb screws and the slide stop from the
pusher assembly. Pull the pusher off the end of the
slide board.
2. Remove the mounting screws from the slide board and
blade shield.
3. To totally disassemble the pusher assembly, remove
the acorn and hex nuts on the top of the stack and
carefully remove the pusher plates and spacers.
Remove the additional screws if you wish to
disassemble the guide plate.
4. To reassemble, reverse the procedure.
NOTE: Always rinse the tomato slicer in cold or lukewarm
water after it has been washed in hot water.
Hot water makes the slide board expand which may
make it difcult to use the pusher assembly until
the slide board returns to room temperature.
NOTE: After reassembly, you must add tension back to
the blades.
REPLACEMENT PARTS
BLADE ASSEMBLIES
#181TSXLBD316 #181TSXLBD732 #181TSXLBD14 #181TSXLBD38
3/16" 7/32" 1/4" 3/8"
PUSHER HEAD ASSEMBLIES
#181TSXLP316 3/16"
#181TSXLP732 7/32"
#181TSXLP14 1/4"
#181TSXLP38 3/8"
ADDITIONAL PARTS
#181SUCCUPFT
Suction Cup
Foot
08/2023
Produktspecifikationer
| Varumärke: | Garde XL |
| Kategori: | skärmaskin |
| Modell: | 181TSXL732 |
Behöver du hjälp?
Om du behöver hjälp med Garde XL 181TSXL732 ställ en fråga nedan och andra användare kommer att svara dig
skärmaskin Garde XL Manualer
18 September 2025
17 September 2025
17 September 2025
16 September 2025
20 Augusti 2025
10 Augusti 2025
8 Augusti 2025
8 Augusti 2025
7 Augusti 2025
7 Augusti 2025
skärmaskin Manualer
- Estella
- RGV
- GARDE
- Ade
- Sencor
- Avantco
- Emerio
- Dito Sama
- Waring Commercial
- Axis
- Magimix
- Nemco
- RIDGID
- Globe
- Continental Edison
Nyaste skärmaskin Manualer
17 September 2025
16 September 2025
15 September 2025
15 September 2025
15 September 2025
15 September 2025
14 September 2025
13 September 2025
13 September 2025
12 September 2025