Garmin BC 20 Bruksanvisning

Garmin Backkamera BC 20

Läs gratis den bruksanvisning för Garmin BC 20 (38 sidor) i kategorin Backkamera. Guiden har ansetts hjälpsam av 5 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 3 recensioner. Har du en fråga om Garmin BC 20 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/38

BC™ 20 Wireless Backup Camera Installation Instructions.............................................................. 2

BC™ 20 Wireless Backup Camera Installation Instructions.............................................................. 4

BC™ 20 Wireless Backup Camera Installation Instructions.............................................................. 7

BC™ 20 Wireless Backup Camera Installation Instructions............................................................ 10

BC™ 20 Wireless Backup Camera Installation Instructions............................................................ 13

BC™ 20 Wireless Backup Camera Installation Instructions............................................................ 16

BC™ 20 Wireless Backup Camera Installation Instructions............................................................ 19

BC™ 20 Wireless Backup Camera Installation Instructions............................................................ 22

BC™ 20 Wireless Backup Camera Installation Instructions............................................................ 25

BC™ 20 Wireless Backup Camera Installation Instructions............................................................ 28

BC™ 20 Wireless Backup Camera Installation Instructions............................................................ 31

BC™ 20 Wireless Backup Camera Installation Instructions............................................................ 34

Garmin International, Inc.

1200 East 151st Street

Olathe, Kansas 66062, USA

Garmin (Europe) Ltd.

Liberty House, Hounsdown Business Park

Southampton, Hampshire, SO40 9LR UK

Garmin Corporation

No. 68, Zhangshu 2nd Road, Xizhi Dist.

New Taipei City, 221, Taiwan (R.O.C.)

Garmin

and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. BC™ is a

trademark of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin.

December 2013 190-01600-90_0D Printed in Taiwan

BC™ 20 Wireless Backup Camera

Installation Instructions

WARNING

See the Important Safety and Product Information guide in the

GPS device product box for product warnings and other

important information.

Garmin

strongly recommends having an experienced installer

with the proper knowledge of electrical systems install the

device. Incorrectly wiring the power cable can result in damage

to the vehicle or the battery and can cause bodily injury.

When connecting the power cable, do not remove the in-line

fuse holder. To prevent the possibility of injury or product

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place will void the product warranty.

CAUTION

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite

side of the surface.

These installation instructions do not apply to a specific vehicle

type, and are meant as a guide when installing this product on

your vehicle. For questions specific to your vehicle, you should

contact the vehicle manufacturer.

Item Description

Wireless camera PND mount

The PND device must be powered through this mount to

communicate with the camera.

Transmitter

Camera

Camera mounting bracket

Tools Needed

• Drill and 0.36 in. (9.09 mm, or size T) drill bit

• #2 Phillips screwdriver

• Screws, bolts, or cable ties (to secure the transmitter)

• Solderless wire-splice connector or solder and heat-shrink

tubing

• RV sealant (optional)

Camera Mounting Considerations

When selecting a location to mount the camera, observe these

considerations.

• You should test a mounting location before you permanently

mount the camera.

• Installing the camera higher on the back of the vehicle

provides a better viewing angle.

• The included bracket can be clipped onto a license plate or

other similar surface, or it can be fastened to the back of the

vehicle using the included self-tapping, panhead screws.

Transmitter Location and Wiring

Considerations

When selecting a location to install the wireless transmitter,

observe these considerations.

• You should test a proposed installation location before you

permanently install the transmitter.

• Although the transmitter can reliably transmit the video signal

over approximately 45 ft. (13.5 m), the location of the

transmitter can affect this range.

◦ The closer you install the transmitter to the wireless

camera PND mount, the more reliable the signal.

◦ The transmitter provides the best signal when either flat

surface

is pointing toward the wireless camera PND

mount.

◦ Dense metal or appliances

in the path of the transmitter

greatly reduce the transmission distance.

◦ The fewer solid objects that exist between the path of the

transmitter and the device, the more reliable the signal.

• If the distance between the camera and the transmitter

exceeds the length of the included cable, additional

extension cables can be used. A 50 ft. (15 m) extension

cable can be purchased, and more than one extension cable

can be installed. See your Garmin dealer or go to

www.garmin.com for more information.

• The fuse holder located near the transmitter is not

waterproof. Installing the fuse holder in a location that is

exposed to the elements is not recommended.

• The connector between the camera and the transmitter is not

waterproof. If you make this connection in a location exposed

to the elements, you must make sure that the connection is

waterproof.

Testing the Camera and Transmitter

Location

Temporarily secure the camera in the preferred mounting

location.

Temporarily place the transmitter in the preferred installation

location, and connect it to power and to the camera.

TIP: If you do not want to splice into the wiring of your

vehicle for this test, you can connect the transmitter and

camera to a 12 Vdc battery.

Test the transmitter for correct operation by applying power

to the PND device using the wireless camera PND mount.

If you do not see video on the device at the preferred

installation location, move the transmitter to another location

and test it again.

Repeat steps 2–3 until the transmitter operates correctly.

Test the camera view by observing the video on the device.

If the camera does not provide the optimal view for your

vehicle, move it to another location and test it again.

Repeat steps 5–6 until the camera mounting location

provides the optimal view for your vehicle.

TIP: Make note of which direction is up when you are testing

the camera view to ensure correct permanent installation.

Mounting the Camera

Before you permanently mount the camera, you should test the

mounting location for the optimal view for your vehicle (Testing

the Camera and Transmitter Location).

If you have already connected the camera to the bracket, you

must first disassemble it.

Place the bracket

in the mounting location.

Select an option:

• If you are mounting the bracket directly on the surface of

your vehicle, mark the locations of the two holes on the

bracket

• If you are installing the bracket on a license plate, remove

one of the license plate screws and clip the bracket in

place so the hole on the bracket

lines up with the hole

on the license plate.

Secure the bracket to the vehicle using either the included

self-tapping screws

or the license-plate screw you

removed in step 2

Place the camera in the bracket, and determine the best

place for the camera cable

to enter the vehicle.

Using an appropriate drill bit, drill a hole for the camera cable

to enter the vehicle.

Feed the camera cable through the hole and route it to the

transmitter location.

15 m (50 ft.) extension cables can be purchased separately,

if needed.

Secure the camera in the bracket using the included hex

bolts

Adjust the angle of the camera and tighten the hex bolts

using the included hex key.

Apply RV sealant around the cable where it enters the

vehicle (optional).

Installing the Transmitter

Before you permanently install the transmitter, you must test the

installation location for correct operation (Testing the Camera

and Transmitter Location).

Secure the transmitter to the installation location using

hardware appropriate for the location, such as screws, bolts,

or cable ties.

The fuse holder located near the transmitter is not

waterproof. Installing the fuse holder in a location that is

exposed to the elements is not recommended.

Connect the camera and transmitter cables.

The connector between the camera and the transmitter is not

waterproof. If you make this connection in a location exposed

to the elements, you must make sure that the connection is

waterproof.

Connect the power cable

from the transmitter to a 12–

24 VDC power source, preferably a reverse lamp

, using a

solderless wire-splice connector (not included).

NOTE: Connecting the transmitter to an always-on

12-24 VDC source (such as a running lamp) instead of a

reverse lamp requires you to manually switch power to the

transmitter. The transmitter may drain your vehicle battery if

it is left on.

If you did not use a solderless wire-splice connector, solder

and heat-shrink the electrical connections to protect them

from the elements.

Using the Camera

The camera shows video on the device in different ways,

depending on how you connected the power to the transmitter.

Select an option to show video:

• If you connected the transmitter to a reverse lamp

(recommended), place the vehicle into reverse. The

device automatically shows video from the backup

camera.

• If you connected the transmitter to a running lamp or other

steady 12 VDC source, select the camera icon on the

device to show video from the backup camera.

Select an option to resume normal device operation:

• If you connected the transmitter to a reverse lamp

(recommended), take the vehicle out of reverse. The

device automatically resumes normal operation.

• If you connected the transmitter to a running lamp or other

steady 12 VDC source, select the camera icon on the

device to resume normal operation.

Aligning the Guidance Lines

Guidance lines provide a visual representation of the vehicle's

path when in reverse. For best reference, they should be

aligned to reflect the outside edges of the vehicle.

Position the vehicle with one side closely aligned to a curb,

driveway, or parking stall lines.

You may want to position the vehicle in the center of a

parking stall, and then pull forward into the next stall. This

allows you to use the parking stall lines in the rear of the

vehicle as reference points for alignment.

The curb, driveway, or parking stall lines should be clearly

visible on the device.

From the camera view, select > Adjust.

Produktspecifikationer

Varumärke:	Garmin
Kategori:	Backkamera
Modell:	BC 20
Inbyggd display:	Ja
Vikt:	11500 g
Förpackningens vikt:	14.8 g
Beeldscherm:	LED
Processorfrekvens:	360 MHz
USB uttag:	Ja
Ethernet LAN:	Ja
Integrerad minneskortläsare:	Nee
Marknadspositionering:	Thuis & kantoor
Förpackningsmått (BxDxH):	540 x 530 x 420 mm
Antal USB 2.0-portar:	1
Strömförbrukning (i standby):	45 W
Strömförbrukning (när avstängd):	1 W
Internminne:	128 MB
Bildformat som stöds:	BMP, JPEG XR, TIF
Strömförbrukning (PowerSave):	10 W
Energisparläge:	Ja
Stöder Mac-operativsystem:	Mac OS X 10.3 Panther, Mac OS X 10.4 Tiger, Mac OS X 10.5 Leopard, Mac OS X 10.6 Snow Leopard
Mac-kompatibilitet:	Ja
Stöder Linux:	Ja
Maximal-upplösning:	1200 x 1200 DPI
Antal bläckpatroner:	1
Skriv ut färger:	Zwart
Medietyper för papperslåda:	Bond paper, Envelopes, Labels, Plain paper, Recycled paper
Utskriftsteknik:	Laser
Standardgränssnitt:	Ethernet, USB 2.0
Utskriftsupplösning svart:	600 x 600 DPI
Utskriftshastighet (svart, standardkvalitet, A4/US Letter):	23 ppm
Att skriva ut:	Zwart-wit afdrukken
Duplexutskrift:	Nee
Indikation på användning (max):	12000 pagina's per maand
Digital avsändare:	Nee
Förstora/förminska kopior:	25 - 400 procent
Kopieringshastighet (svart, standard, A4):	22 cpm
Första kopieringstiden (svart, normal):	12 s
Maximal kopieringsupplösning:	1200 x 1200 DPI
Att kopiera:	Zwart-wit kopiëren
Skanna:	Mono-scannen
Optisk scanningsupplösning:	4800 х 4800 DPI
Max. scangebied:	A4 / Letter (216 x 297) mm
Modemhastighet:	33.6 Kbit/s
Faxminne:	320 pagina's
Försenad faxöverföring:	Ja
Vidarebefordra fax:	Ja
Fax:	Zwart-wit faxen
Total ingångskapacitet:	250 vel
Maximal ingångskapacitet:	251 vel
Total uteffekt:	80 vel
Maximal pappersstorlek i ISO A-serien:	A4
ISO A-seriens mått (A0...A9):	A4, A5, A6
Genomsnittlig strömförbrukning (driftsresultat):	420 W
Dags till första sidan (svart, normal):	9 s
Totalt antal inmatningsfack:	1
JIS B-seriens storlekar (B0...B9):	B5
ISO C-seriens storlekar (C0...C9):	C5, C6
Maximala tryckmått:	210 x 297 mm
ISO B-seriens mått (B0...B9):	B5
Grå nivåer:	10
Maximal skanningsupplösning:	4800 x 4800 DPI
Duplex skanning:	Nee
Maximalt antal kopior:	99 kopieën
Dubbelsidig kopiering:	Nee
Dubbelsidig faxning:	Nee
Faxöverföringshastighet:	3 sec/pagina
Maximalt antal kortnummer:	200
Serveroperativsystem som stöds:	Windows Server 2008, Windows Server 2008 R2, Windows Server 2008 x64
Mått (B x D x H):	416 x 415 x 319 mm
Allt-i-ett-funktioner:	Copy, Fax, Print, Scan
Färgfunktioner allt-i-ett:	Nee
Wifi:	Nee
AC-ingångsspänning:	220 - 240 V
AC-ingångsfrekvens:	50 - 60 Hz
Utmatning av färgdjup:	16 Bit
N-i-1 kopieringsfunktion (N=):	4
Fax geheugen:	4 MB
Kopiera utan PC-inblandning:	Ja