GE JXS77BB Bruksanvisning
Läs gratis den bruksanvisning för GE JXS77BB (2 sidor) i kategorin Ugn. Guiden har ansetts hjälpsam av 17 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 9 recensioner. Har du en fråga om GE JXS77BB eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
Installation Instructions
Body Side Kit For End of the Counter Installation
Tools Required:
#2 Phillips screw driver
Installing the Kit
This Body Side Kit must be installed prior to installing the Range in position.
Locate the body side keyway holes over the heads of the panel supports.
A
A1 Place the three panel supports in the 3 square holes of the vertical side trim and rotate 45° as shown below.
( May require Pliers) See illustration on back page.
A3 Insert 1” screw through shoulder rivet. Place the 1/2” spacer over the end of the 1” screw. Place the spacer-
shoulder rivet-screw assembly through washer. Install assembly in place of the screw removed in A2. (See
illustration on back page.)
A4
Pub. No. 31-10451
229C4053P434
Push the body side forward locking the slots of the keyway holes on the side panel supports.
A5
Place the longest screw (1-1/2” ) through the top hole of the body side at the rear of the range. Slide the spacer
(1-1/4”) over the screw and attach the screw to the hole in the rear of the range above the louvers. Do not tighten.(If
a backsplash kit is used in conjunction with this kit, use the shorter spacer found in the backsplash kit.) See
illustration on back page.
A6
Lift the rear of the body side to close the gap between the cooktop glass and the body side. Tighten the screws
from steps A6 and A7.
A7
Place the short (3/8” long) hex head screw through the bottom hole in the rear of the body side and attach to the
lower section of the range. See illustration on back page, Do Not Tighten.
A8
To stabilize the bottom front corner of the body side-range assembly, place the clip over the inside flange of the
body side and the outside flange of the vertical side trim, as shown in illustration. Start by raising the front corner
of the range by turning the leveling leg downward, to provide more clearance for attaching clip. See illustration on
back page for details of attaching clip. (Hold the body side and the vertical side trim close for easier assembly
of the clip.) See Illustration on back page.
A9
Refer to the Installation Instructions included with the range to place the range into kitchen location.
A10
1/4” Nut Driver
Pliers
Parts Supplied:
3 Panel Supports
1 Body Side
1/2” Spacer
1-1/4” Spacer
Clip
Shoulder Rivet
Washer
#8-3/8” Long
Hex Screw
#8-1” Long Screw
#8-1-1/2” Long Screw
Use these instructions to mount the Body Side Kit on either side of the Slide-In Range.
Remove the hex head screw at the top end of the vertical side trim as shown in the illustration on back page.
A2
1
Produktspecifikationer
| Varumärke: | GE |
| Kategori: | Ugn |
| Modell: | JXS77BB |
Behöver du hjälp?
Om du behöver hjälp med GE JXS77BB ställ en fråga nedan och andra användare kommer att svara dig
Ugn GE Manualer
12 September 2025
1 April 2025
31 Mars 2025
9 Januari 2025
8 Januari 2025
7 Januari 2025
28 December 2024
28 December 2024
28 December 2024
17 December 2024
Ugn Manualer
- Thermador
- Furrion
- Leisure
- Sam Cook
- Zenith
- Castor
- Respekta
- Bifinett
- Ufesa
- Ferroli
- Qlima
- WLA
- High One
- Wolkenstein
- Redmond
Nyaste Ugn Manualer
21 Oktober 2025
20 Oktober 2025
20 Oktober 2025
20 Oktober 2025
19 Oktober 2025
19 Oktober 2025
18 Oktober 2025
18 Oktober 2025
18 Oktober 2025
17 Oktober 2025