GE ZV800BJBB Bruksanvisning

GE Fläktkåpa ZV800BJBB

Läs nedan 📖 manual på svenska för GE ZV800BJBB (24 sidor) i kategorin Fläktkåpa. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/24

If you have questions,call 800.626.2000 or visit our website at: www.monogram.com

Installation

Instructions

36” Chimney Vent Hood

ZV800

Safety Information

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT —Save these instructions for

local inspector’s use.

• IMPORTANT —Observe all governing

codes and ordinances.

•Note to Installer —Be sure to leave these

instructions with the Consumer.

•Note to Consumer —Keep these instructions

with your Owner’s Manual for future reference.

•Skill Level —Installation of this appliance requires

basic mechanical and electrical skills.

•Completion Time — 1 to 3 Hours.

•Proper installation is the responsibility of the installer.

Product failure due to improper installation is not covered

under the warranty.

For Monogram local service in your area, 1.800.444.1845.

For Monogram service in Canada 1.888.880.3030

For Monogram Parts and Accessories, call 1.800.626.2002.

CAUTION:

Due to the weight and size of these vent hoods and to

reduce the risk of personal injury or damage to the product,

TWO PEOPLE ARE REQUIRED FOR PROPER INSTALLATION.

PRUDENCE :

À cause du poids et de la taille de ces hottes et pour

reduire le risque de blessures et de dommages, IL FAUT

DEUX PERSONNES POUR FAIRE L’INSTALLATION

CORRECTEMENT.

WARNING:

To reduce the risk of fire or electrical shock, do not

use this range hood with any external solid-state speed

control device. Any such alteration from original factory

wiring could result in damage to the unit and/or create an

electrical safety hazard.

ADVERTISSEMENT :

Pour réduire le risque d’incendie ou de choc électrique,

il ne faut pas utiliser cette hotte avec un régulateur de

vitesse électronique externe. Toute modification de ce

type du branchement d’usine peute endommager

l’appareil ou créer un risque de choc électrique.

TO REDUCE THE RISK OF FIRE, USE ONLY METAL

DUCTWORK.

WARNING: TO REDUCE THE RISK OF FIRE,

ELECTRICAL SHOCK OR INJURY TO PERSONS, OBSERVE

THE FOLLOWING:

A. Use this unit only in the manner intended by the

manufacturer. If you have any questions, contact the

manufacturer.

B. Before servicing or cleaning unit, switch power off at

the service panel and lock service panel to prevent

power from being switched on accidentally. If the

service panel cannot be locked, fasten a tag or

prominent warning label to the panel.

ADVERTISSEMENT :

POUR RÉDUIRE LE RISQUE D’INCENDIE, DE CHOC

ÉLECTRIQUE OU DE BLESSURES, IL FAUT OBSERVER LES

REGLES SUIVANTES:

A. Utiliser cet appareil uniquement de la maniére prévue

par le fabricant. En cas de question, consulter le

fabricant.

B. Avant toute intervention ou nettoyage, couper

l’alimentation électrique au disjoncteur et verrouiller

le panneau du disjoncteur pour éviter la mise sous

tension accidentelle. S’il n’est pas possible de

verrouiller le panneau du disconcteur, attacher un

placard ou une étiquette trés visible au panneau.

•For general ventilating use only. Do not use to exhaust

hazardous or explosive materials or vapors.

•Structural framing, installation work and electrical

wiring must be done by qualified person(s).

In accordance with all applicable codes and

standards including fire-rated construction.

•Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent back drafting. Follow the

heating equipment manufacturer’s guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE), and the local code authorities.

•Local codes vary. Installation electrical connections and

grounding must comply with applicable codes. In the

absence of local codes, the vent should be installed in

accordance with National Electrical Code ANSI/NFPA

70-1990 or latest edition.

CAUTION: To reduce risk of fire and to

properly exhaust air, be sure to duct air outside – do not

vent exhaust air into spaces within walls or ceilings or into

attics, crawl spaces, or garages.

PRUDENCE : Il faut prendre soin d’installer

un conduit vers l’extérieur pour réduire le risque d’incendie

et pouvoir évacuer l’air correctement. Il ne faut pas évacuer

l’air correctement. Il ne faut pas évacuer l’air dans l’espace

entre les parois d’un mur, un plafond ou un grenier,

un espace sanitaire ou un garage.

INSTALLATION OPTIONS

WALL-MOUNTED INSTALLATIONS

This hood may be installed onto a wall and vented to the

outdoors, or it can be installed for recirculating operation.

All necessary parts for a recirculating operation are shipped

with the hood. No kits required.

UNDER-CABINET INSTALLATIONS

The hood may be installed beneath a cabinet. The cabinet must

measure at least 20” from the bottom frame to the inside top.

See page 19.

•Both vented and recirculating operation can be accomplished

in an under-cabinet installation

(Custom cabinet modification

is required for recirculating operation.)

Design Information

CONTENTS

Design Information

Product Dimensions and Clearances ..................................................3

Installation Options ................................................................................3

Advance Planning, Ductwork, Framing ..............................................4

Power Supply ..........................................................................................4

Duct Fittings..............................................................................................5

Installation Preparation

Tools and Materials Required ..............................................................6

Remove the Packaging ..........................................................................6

Wall Mount Installations ........................................................................7

Installation Below a Wall Cabinet ........................................................7

Check Installation Hardware ................................................................8

Ductwork, Wiring Locations..................................................................9

Wall-Mounted Installation – Vented to the Outside

Step 1, Install Framing for Hood Support............................................9

Step 2, Install Mounting Bracket........................................................10

Step 3, Install Duct Bracket ................................................................10

Step 4, Prepare the Hood ....................................................................11

Step 5, Mount the Hood ......................................................................11

Step 6, Connect Ductwork ..................................................................12

Step 7, Connect Electrical....................................................................12

Step 8, Install Duct Covers ..................................................................13

Step 9, Install Filters..............................................................................13

Step 10, Finalize Installation ................................................................13

Wall-Mounted Installation – Recirculating

Ductwork, Wiring Locations................................................................14

Step 1, Install Framing for Hood Support..........................................14

Step 2, Install Mounting Bracket........................................................15

Step 3, Prepare the Hood ....................................................................15

Step 4, Mount the Hood ......................................................................16

Step 5, Size and Cut Duct Piece ........................................................16

Step 6, Connect Electrical....................................................................17

Step 7, Install Duct Covers ..................................................................17

Step 8, Install Filters..............................................................................18

Step 9, Finalize Installation ..................................................................18

Under-Cabinet Installation

Cabinet Requirements ..........................................................................19

Ductwork, Wiring ..................................................................................19

Step 1, Install Framing for Hood Support..........................................20

Step 2, Prepare the Hood ....................................................................20

Step 3, Cut the Opening........................................................................21

Step 4, Install Side “L” Brackets ........................................................21

Step 5, Remove Side Screw ................................................................21

Step 6, Mount the Hood ......................................................................22

Step 7, Complete Installation and Connect Ductwork....................22

Step 8, Connect Electrical....................................................................23

Step 9, Install Rear Mounting Screws ..............................................23

Step 10, Install Filters............................................................................23

PRODUCT DIMENSION AND

CLEARANCE

The vent hood must be installed 24” min., and 30” max. above

the cooking surface. The telescopic duct cover conceals the

ductwork running from the top of the hood to the ceiling.

The duct cover is sized to reach 8 ft. to 10 ft. ceiling heights.

The hood installation height, from the cooking surface to the

bottom of the hood, depends upon ceiling height.

24” Min.

30” Max.

*24” Min.

* Height to

Ceiling

1-1/2”

12-15/16” at Sides,

13-11/16” at Center

35-7/8”

* The Supplied Duct Cover Fits 8 ft. to 10 ft.

Ceiling Heights

*Depending on Cabinet Height

NOTE: The vent hood

canopy extends

forward 5-7/8”.

Produktspecifikationer

Varumärke:	GE
Kategori:	Fläktkåpa
Modell:	ZV800BJBB
Färg på produkten:	Zwart
Värmekälla:	Electrisch
Bredd:	- mm
Djup:	- mm
Höjd:	- mm
Snäll:	Contactgril
Typ av material (överst):	Grillplaat
Antal brännare/kokzoner:	2 zone(s)
Tillgångar:	- W
LED-indikatorer:	Power, Temperature
Inbyggd funktion:	Nee
Vormfaktor:	Tafelblad
Sladdförvaring:	Ja
Justerbar termostat:	Ja
Antihalkfötter:	Ja
Totala tillgångar:	- W
Avtagbar spillplatta:	Ja
Non-stick beläggning:	Ja
Lock:	Nee
Hjulhjul:	Nee
Kokyta form:	Rechthoekig
Ben:	Ja
Rökfunktion:	Nee