GRE RKJ14 Bruksanvisning

GRE dammsugare RKJ14

Läs nedan 📖 manual på svenska för GRE RKJ14 (19 sidor) i kategorin dammsugare. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/19
820109
Nederlands Bodemreiniger - Gebruiksaanwijzing
2
8
14
20
26
32
38
Thank you for choosing Jet Unit to clean your pool. We
hope that you will enjoy using your new Jet Unit to maintain
your swimming pool for years to come.
The Jet Unit is the only fully automatic robotic pool cleaner
with a powerful jet drive propulsion system.
Before you begin to use the cleaner, please take a few
minutes to carefully read the Operator Instructions. Again,
thank you for choosing our Jet Unit.
our
Dear Customer,
timer
socket
side plate
handle
wheel
body
floating cable
power switch
ON/OFF
transformer 230 V only
transformer cable plug
lock pin
floating cable plug
jet valve housing
jet outlet
1
fuse
IMPORTANT
CAUTION: Do not switch the pool cleaner “ON” if it is not fully immersed in
water. Operating the cleaner out of water will cause severe damage
immediately and will result in loss of warranty.
Allow the cleaner to remain in the pool for 15 to 20 minutes following the
end of its cleaning cycle. This will allow the motors to cool adequately. Do
not leave the cleaner in the pool all the time. Always remember to turn the
power supply “OFF” and unplug it from the power outlet before removing
the cleaner from the pool.
WARNING: Your Cleaner should not be used while people are
swimming in the pool.
Safety Note
- The unit must be supplied through a residual current device (RCD)
having a rated residual operating current not exceeding 30 mA
- The connection to the branch circuit should be consistent with the local
and national wiring rules (electrical code).
- Mishandling of the unit can result in leakage of lubricants.
- If the supply cord is damaged, it must be replaced by the manufacturer’s
service agent or a qualified and trained person in order to avoid hazards.
2
Operating Instructions
3
8 4
2
6
Your new automatic pool cleaner contains:
A. Robotic Pool Cleaner and floating cable.
B. Power Supply (transformer)
Please read this Manual completely before operating your Pool Cleaner.
1. Place the power supply (transformer) at least three meters (10 feet) from the pool. (See figure
2). The transformer should not be left out in the rain or placed in puddles of water. The
transformer will supply very low voltage (12V) to the cleaner.
2. Uncoil the cable (See figure 3 ).
3. Make sure that the power supply switch is in the “OFF” position (See figure 4).
4. Plug the cable into the socket on the power supply (See figure 5):
a Fit exactly the and the from cable plug with the corresponding key and slots . key slots
from the transformer socket.
b . Push the plug into the socket of the transformer all the way in.
c. Once the plug is in, rotate the plug to the right to lock it into place.
5. Place the unit in the water. Turn the unit
side to side in the water to allow air to
escape from the body and then let
the cleaner sink to the bottom of
the pool (See figure 6 ). Then
spread the floating cable over the
surface of the pool as evenly as
possible making sure it is not
tangled or kinked
6. Plug the transformer cord into a
230V three grounded outlet (See figure
8).
½ ½
Power supply
Power supply
key
slots
PLUG SOCKET
key
slots
SOCKET
3

Produktspecifikationer

Varumärke: GRE
Kategori: dammsugare
Modell: RKJ14

Behöver du hjälp?

Om du behöver hjälp med GRE RKJ14 ställ en fråga nedan och andra användare kommer att svara dig




dammsugare GRE Manualer

dammsugare Manualer

Nyaste dammsugare Manualer