Hager TXA624D Bruksanvisning

Hager Inte kategoriserad TXA624D

Läs gratis den bruksanvisning för Hager TXA624D (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 4 personer och har ett genomsnittsbetyg på 4.8 stjärnor baserat på 2.5 recensioner. Har du en fråga om Hager TXA624D eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

6LE002722A

TYA624B

Output 4gang shutter 24 V

TYA624D

Output 4gang shutter/blind

24 V

TXA624D

Output 4gang shutter/blind

24 V

6LE002722A1

Safety instructions

Electrical equipment may only be installed and

assembled by a qualied electrician in accor-

dance with the relevant installation standards,

guidelines, regulations, directives, safety and

accident prevention regulations of the country.

Failure to comply with these installation in-

structions may result in damage to the device,

re or other hazards.

Hazard due to electric shock. Disconnect be-

fore working on the device or load. Take into

account all circuit breakers that supply dan-

gerous voltages to the device or load.

Connect one motor per output only. If several

motors are connected, motors or device might

be destroyed.

Use drives with mechanical or electrical nal

position switches only. Check nal position

switches for correct adjustment. Observe mo-

tor manufacturer's data. The device can be da-

maged.

Risk of injury. Use the device to control blind

and shutter drives or awnings only. Do not

switch any other loads.

Observe the motor manufacturer's data regar-

ding change-over time and max. switch-on time

(ED).

These instructions are an integral component

of the product and must be retained by the end

user.

Design and layout of the device

C4C4

C3C3

30V DC

3 5

7 9

4 6 8 10

C1 C3

C2 C4

auto

(1)

(2) (3)

(4) (5)

(6)

(3)

Figure 1: device overview

(1) Slide switch /auto

(2) KNX bus connection terminal

(3) Connections of loads

(4) Labelling eld with cover

(5) Illuminated programming button

(6) Operation button for manual operation per

output with status LED

Function

System information

This device is a product of KNX system and corre-

sponds to the KNX guidelines. Detailed specialised

knowledge obtained from KNX training courses is

required for comprehension. The planning, installa-

tion and commissioning of the device is carried out

with the help of KNX-certied software.

Systemlink commissioning

The function of the device is software-dependent.

The software is to be taken from the product

database. You can nd the latest version of the

product database, technical descriptions as well as

conversion and additional support programmes on

our website.

Easylink commissioning

The function of the device is conguration-depen-

dent. The conguration can also be done using

devices developed specially for simple setting and

start-up.

This type of conguration is only possible with

devices of the easylink system. Easylink stands for

easy, visually supported start-up. Precongured

standard functions are assigned to the in/outputs

by means of a service module.

Functional description

The devices are used to control motor-operated

building ttings such as shutters and blinds via the

KNX bus. The devices have 4 outputs from which

each output can be activated independently.

Correct use

- Switching of electrically driven 24 V motors for

blinds, shutters, awnings and similar hangings.

- Mounting on DIN rail according to

DIN EN 60715 in the distribution box.

Product characteristics

- independent outputs, activation via KNX bus.

- Status display of the outputs on the device.

- manual activation of the outputs on the device

possible, building site operation.

- Position can be started directly.

- 3 Alarms.

- Scene function.

- Forced position by higher-level controller.

Blind actuators only

- Slat position directly controllable.

Operation

Manual operation switch on/off

Bus voltage supply is present.

zPush switch (1) to position .

Manual operation is switched on, the outputs

can be controlled using the operation buttons

(6) independently of each other.

During manual operation, the controller is deac-

tivated via the KNX bus.

Systemlink commissioning: depending on the

programming, the manual operation is activated

permanently or for a time period congured via

the application software.

If the manual operation is blocked via the appli-

cation software, no activation takes place.

zMove switch (1) to position .auto

The manual operation is switched off. Opera-

tion takes place solely via the KNX bus. The

output takes the position predened by the bus

controller.

Operating outputs in manual operation

Operation takes place per output by brief repeated

presses on the operation button (6) (table 1).

Status Behaviour when

briey pressing the

button

Manual operation is

switched on, initial

operation of an output.

Move DOWN, re-

gardless of output

status.

Movement operation

active, status LED of the

button (6) lights up.

Movement operation

stops.

Output is in standby,

status LED of the button

(6) is off.

Movement operation

in opposite direction of

the last movement.

Table 1: manual operation

Information for electricians

Installation and electrical connection

DANGER!

Touching live parts can result in an

electric shock!

An electric shock can be lethal!

Disconnect the connecting cables

before working on the device and

cover all live parts in the area!

CAUTION!

Risk of destruction if parallel connec-

tion of several motors on one output!

Final position switches could fuse

together. Motors, hangings and the

device may be destroyed!

Only connect one motor per

output!

Bn,.:

Produktspecifikationer

Varumärke:	Hager
Kategori:	Inte kategoriserad
Modell:	TXA624D
Färg på produkten:	Wit
Vikt:	5000 g
Bredd:	250 mm
Djup:	170 mm
Höjd:	480 mm
Snäll:	Automatisch
AC-ingångsspänning:	220-240 V
AC-ingångsfrekvens:	50 - 60 Hz
Strömförbrukning (typiskt):	825 W
Torktid:	23 s