Hager VML11414 Bruksanvisning
Hager
Inte kategoriserad
VML11414
Läs gratis den bruksanvisning för Hager VML11414 (4 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 5 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 3 recensioner. Har du en fråga om Hager VML11414 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
Design 10 Two Row Consumer Unit
Instructions/Data Sheet
This Consumer Unit and Hager devices conform with the following standards:
Consumer Unit: BS EN 61439-3 including Annex ZB.
Switch-disconnectors: BS EN 60947-3.
Residual Current Circuit Breaker (RCCB): BS EN 61008-1
Residual current operated circuit breaker with integral overload (RCBO): BS EN 61009-1
Miniature Circuit Breaker (MCB): BS EN 60898-1
Installation Instructions:
All product(s) must be installed by a suitably competent electrician
Giving consideration to their intended use and in accordance with the
current edition of BS 7671 (IET Wiring Regulations).
The Electricity at Work regulations and the Health and Safety at Work Act
shall be complied with.
Only equipment and arrangements specied in Hager’s technical
documentation / catalogue shall be used.
Install in the horizontal plane only.
For guidance when making connections in a consumer unit electrical
safety rst /BEAMA document “Guidance for installers when making
connections in consumer units” is available from hager.co.uk/63026.htm
Important notice:
To prevent potential overheating from loose connections the installer
shall check connections are tight to the torque levels stated in these
instructions prior to energizing this board. This check should include
factory made connections which may have loosened in transit.
Good workmanship and proper materials must be applied by the installer.
The cable entry method shall, as far as reasonably practical, maintain the
non-combustable arrangement of the enclosure. Account shall be taken of
these instructions.
Lift door and loosen the two captive screws until the cover can be
removed. The units have multiple xing points that will suit No.8 & No.10 screws
These metal units are provided with knockouts suitable for
use with 100x50mm trunking, 50x50mm trunking, 40x25mm
trunking and also large rear knockouts. Grommet strip is
provide to protect the cables when entering the board.
Rear cable entries shall enter thorough selected rear Knockout; once
the Knockout is removed apply the grommet strip provided.
Grommet strip lengths: – 79mm, Small EKO Large EKO – 127mm
Rear EKO – 255mm
Note: Only BASEC approved cable should be used
1.0mm2 to 16mm2 for outgoing cables
Up to 35.0mm2 for incoming live cables
Single conductors below 1.5mm² need to be doubled back in the terminal
bar
Cable entry facilities:
Wall Fixing:Removal of Front Cover:
Additional Extras
Accessory Ref.
Cable protector plate
Can be used on the rear knockouts to smooth any
sharp edges
Insulated:
VM02CE
Metal:
VM01CE
Cable Clamp
Can be used to clamp meter tails in place when
entering main switch
VA10MT
GB
1 ZD0829 - Issue 4 9-16
ZD0829ZD0829
Produktspecifikationer
| Varumärke: | Hager |
| Kategori: | Inte kategoriserad |
| Modell: | VML11414 |
Behöver du hjälp?
Om du behöver hjälp med Hager VML11414 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Hager Manualer
2 April 2025
2 April 2025
2 April 2025
2 April 2025
2 April 2025
2 April 2025
2 April 2025
2 April 2025
2 April 2025
1 April 2025
Inte kategoriserad Manualer
- Jupio
- Mousetrapper
- Neets
- Essenza
- ACE
- Morris
- Volkswagen
- Sunstech
- Chuango
- Monacor
- Phase One
- Electrify
- Life Fitness
- Epiphan
- Vinotemp
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025