Hamilton Buhl LCP/12/901BT Bruksanvisning

Läs gratis den bruksanvisning för Hamilton Buhl LCP/12/901BT (4 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 2 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 1.5 recensioner. Har du en fråga om Hamilton Buhl LCP/12/901BT eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Sida 1/4
WIRELESS HEADPHONE SYSTEM
(For W900-MULTI, W900-BLTM, W901-MULTI)
INSTRUCTION MANUAL
2
Wireless Headphone System
W900-BLTM Bluetooth Transmitter Setup
1. Extend the antenna vertically to full height.
2. Plug the 12V/1A power adapter into DC12V socket on the rear of transmitter. Insert power
adapter into power outlet.
internal rechargeable battery. Adjust to OFF to turn off the unit.
4. Plug the adapter into the DC12V jack to charge the battery. The CHARGE LED will be lit. When
fully charged, LED will turn off.
5. PAIR button is used to pair with Bluetooth devices. The device ID is V001. Push the SW
button when pairing and the blue color LED with ash when pairing is successful.
6. To select channel, press CH SEL on the front panel of transmitter (bottom left side). Press again
for the next channel.
7. The LED color indicates the selected channel color.
8. Stereo LED indicates Mono or Stereo mode. ON means stereo mode and OFF means mono.
Press and hold CH SEL push button for 3 seconds to toggle mode and the LED will change state.
9. Connect the 3.5mm stereo plug into any stereo mini jack sources of your choice to transmit
contents wirelessly to W901-MULTI.
10. Adjust volume control on the sound source to the desired output level.
11. Use microphone: Connect mono-type mic jack into marked mic socket on the rear panel of
transmitter. (microphone not included)
12. IMPORTANT: When not using the microphone, remove the microphone plug from the back of the
transmitter to resume normal operation.
13. When battery is low, the “Stereo” LED will ash red and stop all other
functions. Please plug power adapter and charge the battery immediately.
AC12V
BATT
ON
OFF
SW LED
PAIR
CHARGE
LED
LINE IN
Stereo
CH SEL
Transmitter
CH1 CH2 CH3 CH4
MODEL: W900-BLTM
W900-MULTI Transmitter Setup
1. Extend the antenna vertically to full height.
2. Plug the 12V/1A power adapter into DC12V socket on the rear of transmitter. Insert power adapt-
er into power outlet.
3. Select the desired channel by pushing the CH SEL button on the front panel of the transmitter.
Continue to press the channel selector until the desired channel color is lit.
4. Stereo red LED shows the transmission is in Mono or Stereo. On means Stereo mode; OFF
means mono. Press and hold
CH SEL push button for 3 seconds will toggle mode and the LED will change state.
5. Connect the 3.5mm stereo plug into any stereo mini jack sources of your choice to transmit con-
tents wirelessly to W901-MULTI.
6. Adjust volume control on the sound source to the desired output level.
7. Use microphone: Connect mono type mic jack into marked mic socket on the rear panel of trans-
mitter. (microphone not included)
8. IMPORTANT: When not using the microphone, remove the microphone plug from the back of the
transmitter to resume normal operation.
AC12V
LINE IN
Stereo
CH SEL
Transmitter
CH1 CH2 CH3 CH4
MODEL: W900-MULTI
3
Wireless Headphone System
Using Your W901-MULTI Wireless Headphones
(Compatible with both the W900-MULTI and W900-BLTM models)
Note: Fully charge headphones before using for the rst time. See Instructions.
1. Press and hold the Power button more than 3 seconds to power up the headphone. The selected
channel color will be shown on the CH LED.
2. The channel LED “CH LED” will show ve colors as “Yellow – Blue – Flashing Blue – Green
Red. Blue for Mono mode and Flashing Blue for Stereo mode.
3. Press Power button to next channel until the headphone channel LED color matches with the
transmitter channel LED color, in order to establish proper communications.
4. Adjust the volume control buttons of “Vol +” and “Vol –” to a comfortable listening level.
5. When nished using the headphone, press and hold the “Power” button for 3 seconds to power off
the headphone.
6. When reaching a low battery level, the “CH LED” will ash red for 10 seconds, then the power will
turn off automatically. Please connect power adapter to charge the headphone immediately.
Note: To operate correctly, make sure to select the same color channels for
both transmitter and headphone.
Important: Do not charge the headphone battery for longer than 24 hours.
The charging lead is designed to charge up to six headphones
simultaneously. Disconnect the power adapter plug from the
transmitter, and insert into the socket on the charge lead, as per
illustration (1).
Fit one of the charger lead plugs into the socket on the headphone
as the illustration (2). Check the headphone is in power off state.
Connect power adapter to outlet, and leave overnight (10-12 hours).
The red LED will turn on to indicate charging and it will turn off when
headphones are fully charged.
MODEL: W901-MULTI
VOL- VOL+POWER
CH1 CH2 CH3 CH4
CH LED
Transmitter
W900-Multi W900-BLTM
System Type VHF-FM VHF-FM and Bluetooth
Channels 4 4
Antenna Telescopic Telescopic
Range 100ft 100ft
Audio Input -20 to 20dBm -20 to 20dBm
Power
Output
10mW 10mW
Power
Supply
12 volts DC 12 volts DC
Channel: Color and Frequency
Yellow Blue Green Orange
72.100 MHz 72.500 MHz 72.900 MHz 74.700 MHz
Headphone W901-MULTI
System Type VHF-FM
Channels 4
Speaker 30mm Mylar
Batteries NiNH
Run Time 35 hrs
Weight 10 oz
Wireless Headphone System Specications
1
2

Produktspecifikationer

Varumärke: Hamilton Buhl
Kategori: ej kategoriserat
Modell: LCP/12/901BT

Behöver du hjälp?

Om du behöver hjälp med Hamilton Buhl LCP/12/901BT ställ en fråga nedan och andra användare kommer att svara dig