Harley Davidson J02830 Bruksanvisning

Harley Davidson J02830

Läs gratis den bruksanvisning för Harley Davidson J02830 (2 sidor) i kategorin . Guiden har ansetts hjälpsam av 12 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 6.5 recensioner. Har du en fråga om Harley Davidson J02830 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/2

INSTRUCTIONS

-J02830 REV. 07-16-2003

BULLET CHROME DIRECTIONAL BAR KIT (HDI)

General

This directional bar fits 1999 and later HDI Touring and

FLSTC/I models. Softail models only: This kit will not fit

with the stock saddlebags, part numbers 90476-00 and

90477-00.

This kit contains the following items:

QTY DESCRIPTION PART NO.

1Directional bar assembly 68997-04

2Hex screw, serrated flange 3576

NOTE

A Service Manual for your model motorcycle is available

from any Harley-Davidson dealer.

Installation

To prevent accidental vehicle start-up, which could

cause death or serious injury, disconnect battery cables

(negative cable first) before proceeding.

Disconnect negative (-) battery cable first. If positive (+)

cable should contact ground with negative (-) cable con-

nected, the resulting sparks can cause a battery explosion,

which could result in death or serious injury. (00049a)

1. Refer to the Service Manual and follow the instructions

given to remove the seat and disconnect the battery

cables, negative cable first.

2. See Figure 1. Remove the taillight cover and disconnect

the turn signal wires at the connectors shown in the illustra-

tion. See the TAIL LAMP section of the Service Manual.

3. Remove and discard the existing directional bar from the

motorcycle, and the two hex head bolts and flat washers.

4. Position the new Bullet Directional Bar Assembly to the

rear fender, and secure the bar to the motorcycle using

the two hex screws from the kit.

5. Route the turn signal wires through the grommet in the

fender. Connect the turn signal wires at the connectors

shown in the illustration and replace the taillight cover

IMPORTANT NOTE

After making wire connections and routing wires, check to

make sure that no wires are hanging loose from fender.

Connect positive (+) battery cable first. If positive (+) cable

should contact ground with negative (-) cable connected,

the resulting sparks can cause a battery explosion, which

could result in death or serious injury. (00068a)

6. Connect the battery cables, positive cable first.

7. Refer to the Service Manual, and follow instructions to

install the seat.

After installing seat, pull upward on front of seat to be

sure it is in locked position. While riding, a loose seat

can shift causing loss of control, which could result in

death or serious injury. (00070a)

Check for proper turn signal operation before riding

motorcycle. Weak, intermittent, or non-operational lights

indicate a poor connection or a short in the wires.

Visibility is a major concern for motorcyclists. Improper

turn signal operation may lead to an accident which

could result in death or serious injury.

8. Start the motorcycle and make sure that both turn signals

function properly.

1WARNING

Kit Number 68617-04

Figure 1. Turn Signal Connections

i01526

1. Left turn signal 2. Right turn signal

Produktspecifikationer

Varumärke:	Harley Davidson
Kategori:
Modell:	J02830
Färg på produkten:	Black, Blue
Vikt:	530 g
Bredd:	142.5 mm
Djup:	107.1 mm
Höjd:	53.5 mm
Förpackningens vikt:	842.857 g
Förpackningens bredd:	158 mm
Djuppackning:	66 mm
Förpackningshöjd:	213 mm
Användarmanual:	Ja
Husmaterial:	Metaal
Kraftkälla:	DC
Internationell säkerhetskod (IP):	IP40
Snabbstartsguide:	Ja
Ursprungsland:	China
Kod Storbritanniens handelstull:	85176200
Plug and play:	Ja
Inspänning:	12 - 48 V
Ethernet LAN, dataöverföringshastigheter:	10,100,1000 Mbit/s
Nätverksstandard:	IEEE 802.3x
Förvaringstemperatur:	-40 - 80 °C
Förvaringsfuktighet:	5 - 95 procent
Rackmontering:	Ja
Lämplig för utomhusbruk:	Nee
Redundant strömförsörjning:	Ja
Ethernet-gränssnittstyp:	Gigabit Ethernet
Medeltid mellan fel (MTBF):	300000 uur
Strömförsörjning ingår:	Ja
VLAN=support:	Nee
Power over Ethernet (PoE):	Nee
Stapelbar:	Nee
Växlingskapacitet:	1 Gbit/s
MAC-ställbar:	2000 entries
10G-stöd:	Nee
Dataflödeshantering:	Ja
Växlingstyp:	Unmanaged
Antal grundläggande switchande RJ-45 Ethernet-portar:	4
Antal Gigabit Ethernet (koppar) portar:	4
Bandbreedte:	14 Gbit/s
Typ grundläggande switchande RJ-45 Ethernet-portar:	Gigabit Ethernet (10/100/1000)
Paketbuffertminne:	1.2 MB
Stöd för Jumbo Frames:	Ja
Full duplex:	Ja
Strömförbrukning (typiskt):	5 W
Drifttemperatur (TT):	-40 - 80 °C
Relativ luftfuktighet i drift (VV):	5 - 95 procent
Förpackningsvolym:	2221.16 cm³
Frakthastighet:	10.5 Mpps
Jumbo ramar:	9000
Antal SFP-moduler installerade:	2
DIN-skena montering:	Ja
Lagra och vidarebefordra:	Ja
Vandalbeständig:	Nee
Fiberoptisk kontakt:	SFP
Spänningsskydd:	Ja
Halv duplex:	Ja
Överspänningsskydd i spänning:	4 kV