Hifonics HAC-3000.1D Bruksanvisning
Läs gratis den bruksanvisning för Hifonics HAC-3000.1D (2 sidor) i kategorin mottagare. Guiden har ansetts hjälpsam av 35 personer och har ett genomsnittsbetyg på 4.1 stjärnor baserat på 18 recensioner. Har du en fråga om Hifonics HAC-3000.1D eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
Place terminal in a secure
position so that it won’t
accidentally contact the
negative battery post
Power cable size
and fusing
It is critical to use the proper power
and ground cable. Select the size
listed here for your amplier model.
Always use high quality copper
cable. Visit our website for multi amp
system cable recommendations.
Be sure to use the proper fuse size
for each model. Some models require
an external fuse.
Properly route power,
speaker and RCA cables
through the vehicle.
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplier to
a secure surface. Do not mount
the amplier upside down.
Attach the chassis ground
cable to the amplier
negative terminal. It is
important to make sure this
connection is very tight.
Bare metal
Attach the main power cable
to the amplier +12V. The
cable must run directly to
the battery and be properly
fused and be very tight.
Attach the remote turn on
wire to the amplier remote
output of the source unit.
Connect the RCA cables to
the INPUT connectors. The
OUTPUT can be used to
provide input for a second
amplier.
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
Re-connect the negative
battery terminal making sure it
is securely tightened.
The chassis ground connection
is critical to the performance
of the amplier. Choose a
location that is close to the
amplier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Disconnect
negative battery
terminal
Run Cables
Mount Amplier
Negative Power
Connection
Positive Power
Connection
Remote Turn-on
Connection
Signal Input
Connection
Positive Battery
Connection
Re-connect
Negative Battery
Terminal
Chassis Ground
Be prepared to disarm your vehicle’s alarm and
to enter your radio / source unit code.
Installation
Before you start
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
1
2
3
5
7
6
8
11
12
4
Turn the LEVEL control completely
counter-clockwise to minimum.
Level Control
9
0ga
External 150A
External 200A
External 125A
External 200A
External 400A
Model Fuse Cable
HAC-2000.4D
HAC-3000.4D
HAC-1500.1D
HAC-3000.1D
HAC-5000.1D
Common System Setup
10
POWER
4ch - Full Range
4ch - Mixed Mono
Mono
Connect the speaker cables to the speaker
output connectors. Follow the diagram below
that best ts your speaker conguration.
Recommended Setups Below
Mono Block
4-Channel Mixed Mono
4-Channel Full Range
Mono Block
4-Channel Mixed Mono
4-Channel Full Range
Mono Block
4-Channel Mixed Mono
4-Channel Full Range
Mono Block
4-Channel Mixed Mono
4-Channel Full Range
Produktspecifikationer
| Varumärke: | Hifonics |
| Kategori: | mottagare |
| Modell: | HAC-3000.1D |
Behöver du hjälp?
Om du behöver hjälp med Hifonics HAC-3000.1D ställ en fråga nedan och andra användare kommer att svara dig
mottagare Hifonics Manualer
5 Juli 2025
4 Mars 2025
4 Mars 2025
30 December 2025
5 Oktober 2024
4 Oktober 2024
2 Oktober 2024
2 Oktober 2024
22 September 2024
22 September 2024
mottagare Manualer
- Graupner
- Klipsch
- Black Lion Audio
- Godox
- Powersoft
- Proel
- Electro-Voice
- DB Technologies
- QTX
- Pharos
- Streacom
- BuonaIdea
- Camecho
- Pro-Ject
- Neve
Nyaste mottagare Manualer
19 Oktober 2025
19 Oktober 2025
18 Oktober 2025
18 Oktober 2025
18 Oktober 2025
18 Oktober 2025
17 Oktober 2025
15 Oktober 2025
15 Oktober 2025
15 Oktober 2025