Hifonics HF7BEQ Bruksanvisning
Hifonics
Inte kategoriserad
HF7BEQ
Läs gratis den bruksanvisning för Hifonics HF7BEQ (10 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 2 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 1.5 recensioner. Har du en fråga om Hifonics HF7BEQ eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/10
Operator’s Guide
HF7BEQ
Thank you for purchasing the HIFONICS HF7BEQ 7-Band Equalizer/
two-way crossover. This unit has both a pre-amp equalizer and
crossover to provide the multi-speaker system of your vehicle with
improved sound performance. Please read the entire manual to
ensure proper connections and application.
CAUTION
Always consider consulting a professional audio installer
before installing any audio components. Be careful and take
your time. Do not let wires make contact with metal edges or
hot engine components.
Features
• ILLUMINATED BLUE CONTROL KNOB LEDS
• LOW AND HIGH LEVEL AUDIO INPUTS (SPEAKER LEVEL)
• DESIGNATED SUBWOOFER UNBALANCED OUTPUT
• SUBWOOFER X-OVER FREQUENCY CONTROL
• INPUT LEVEL CONTROL ADJUSTMENT
• FADER CONTROL
• HALF DIN CHASSIS SIZE
• MOUNTING HARDWARE (INCLUDED)
• SEVEN EQUALIZATION BANDS EACH ADJUST +/- 12dB
1
Mounting and Hardware
Prior to mounting, connect the wires
to ensure proper operation.
MOUNTING
1. Select the desired mounting location, either under the dash or
in the dash. Make sure that there is adequate depth for the HF7BEQ.
2. Use the mounting brackets and hardware provided. Make sure
there is proper clearance for the mounting bracket screws when
attaching under the dash. Use caution to ensure there are no wiring
harnesses behind the dash panel (where the mounting
screws are fastened).
3. Route the power, ground, and remote wires away from moving
parts to prevent pinching or shortened wires.
WIRING
1. : The power wire should connect to a constant or Power Wire
switched +12 volt source with a in-line fuse. We recommend (2 Amp)
that you use the radio constant or switch +12 volt source.
2. : Connect the ground wire to a clean chassis ground Gound Wire
point. Be sure to remove all paint and primer to expose clean metal.
Use a ring terminal and lock or star washer to secure the ground wire.
3. : The remote wire should be connected to the source Remote Wire
until remote or antenna wire that provides +12 volts when the
source unit is “on” and 0 volts when the source unit is turned “off.”
2
Produktspecifikationer
| Varumärke: | Hifonics |
| Kategori: | Inte kategoriserad |
| Modell: | HF7BEQ |
Behöver du hjälp?
Om du behöver hjälp med Hifonics HF7BEQ ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Hifonics Manualer
23 September 2024
18 September 2024
18 September 2024
9 September 2024
9 September 2024
9 September 2024
1 September 2024
24 Augusti 2024
24 Augusti 2024
23 Augusti 2024
Inte kategoriserad Manualer
- Bxterra
- Rosieres
- MoTip
- Aeris
- Finder
- Majority
- Steinberg
- Draytek
- Proteca
- Buffalo
- POLARIS
- Kernau
- Helix
- Rega
- Basil
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025