Hobart 6614 Bruksanvisning
Läs gratis den bruksanvisning för Hobart 6614 (12 sidor) i kategorin Sågmaskin. Guiden har ansetts hjälpsam av 15 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 8 recensioner. Har du en fråga om Hobart 6614 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/12
FORM 34527 Rev. B (August 2011)
MODEL 6614 MEAT SAW
MODEL
6614 ML-134096
PREVIOUS MODELS COVERED BY THIS MANUAL:
6614 ML-134050
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937 332-3000
www.hobartcorp.com
– 2 –
Installation, Operation, and Care of
MODEL 6614 MEAT SAW
SAVE THESE INSTRUCTIONS
GENERAL
The 6614 Meat Saw is rugged, durable, and easy to clean. The saw is equipped with a water resistant
3 HP electric motor and direct gear drive transmission that provides a blade speed of 3500 feet per minute.
The carriage (Fig. 1) has stainless steel ball bearings providing easy travel and dependability. The shaped
front edge of the carriage is comfortable to the operator's body even when leaned on during movement.
The carriage lock is standard. The upper pulley cover and bafe are stainless steel.
Table, carriage, pulleys, guides, and wiper assemblies can be quickly removed without tools for ease of
cleaning. Moving parts are enclosed but accessible. The blade is guarded above and below the cutting
zone. The pusher plate is provided to eliminate the need of handling items close to the blade; it can ride
on the right "anged-end" of the carriage so you keep your hands away from the cutting edge of the blade.
For electrical specications above 250 volts, a transformer provides a 115 volt control circuit voltage.
One long-life blade is furnished with each saw as standard equipment. This blade cannot be re-sharpened;
replacement blades are available through your local Hobart Service Ofce.
© HOBART, 1995, 2000
PL-41501-1
UPPER PULLEY COVER
COLUMN GUARD
GAUGE PL EAT
TABLE (RIGHT)
GAUGE PL E HANDLEAT
LOCK LEVER
LOWER COVER (SCRAP N)PA
LEGS
FEET
CARRIAGE LOCK
CARRIAGE
TABLE (LEFT) SAW BLADE
UPPER GUIDE AND GUARD
SWITCH KNOB
Fig. 1
– 3 –
INSTALLATION
UNPACKING AND ASSEMBLY
Immediately after unpacking the meat saw, check for possible shipping damage. If the meat saw is found
to be damaged, save the packaging material and contact the carrier within 15 days of delivery.
Prior to installation, test the electrical service to make sure it agrees with the specications on the machine
data plate located on the column.
Packed in a packet attached to the table compartment are the pusher plate and the gauge plate handle.
Place the pusher plate in its storage location under the carriage support (Fig. 2). Assemble the gauge
plate handle to the gauge plate support by screwing the stud into the threaded hole (Fig. 3).
LEVELING
Place the saw in its operating location. Using a spirit level, level the meat saw front-to-back and side-to-
side by turning the threaded feet in or out.
PL-52107
Hand Knob
Upper Guide
and Guard
PL-41502-1
CARRIAGE
SUPPORT
SAW BLADE
CARRIAGE
PUSHER PL EAT
HAND KNOB
PL-41503-1
GAUGE PL E HANDLEAT
Disconnect the electrical power to the machine and follow lockout / tagout
procedures.
SAW BLADE
The saw blade must be installed so the teeth point to the right
and down (Fig. 4).
UPPER GUIDE AND GUARD ASSEMBLY
When the saw is off, the hand knob (Fig. 4) can be used to raise
or lower the upper guide and guard assembly so the cutting
zone is only as high as necessary for the piece being cut. The
hand knob is not loosened during raising or lowering — it should
remain tightly secure.
Fig. 2 Fig. 3
Fig. 4
Produktspecifikationer
| Varumärke: | Hobart |
| Kategori: | Sågmaskin |
| Modell: | 6614 |
Behöver du hjälp?
Om du behöver hjälp med Hobart 6614 ställ en fråga nedan och andra användare kommer att svara dig
Sågmaskin Hobart Manualer
12 September 2024
12 September 2024
Sågmaskin Manualer
- Lux Tools
- Craftsman
- Bosch
- Duro
- Silverline
- Homelite
- Total
- Sovereign
- Tacklife
- DeWalt
- Clarke
- Atika
- Florabest
- Ryobi
- Maestro
Nyaste Sågmaskin Manualer
3 April 2025
3 April 2025
1 April 2025
1 April 2025
1 April 2025
1 April 2025
1 April 2025
1 April 2025
29 Mars 2025
29 Mars 2025