Hoffman A4044LP Bruksanvisning
Hoffman
Inte kategoriserad
A4044LP
Läs gratis den bruksanvisning för Hoffman A4044LP (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 9 personer och har ett genomsnittsbetyg på 3.7 stjärnor baserat på 5 recensioner. Har du en fråga om Hoffman A4044LP eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
© 2013 Pentair Equipment Protection PH 763 422 2211 • hoffmanonline.com 87567803Rev. B P/N 23155002
Repainting Homan Standard Paint
Check with the paint manufacturer to insure the paint you are applying is compatible
with the paint on the Homan product.
Homan uses the following TGIC polyester powder coating nishes on standard
catalog items:
1. ANSI 61 Gray
2. RAL 7035
3. White
Refer to homanonline.com for the specic paint nish of the product that you
propose to repaint. When in doubt, consult your local Homan distributor.
IMPORTANT: For best adhesion results, correct surface preparation before
repainting is essential.
GENERAL: All Homan TGIC polyester powder coated nishes can be repainted.
IMPORTANT: For best renishing results, always follow the specic instructions
provided by your paint manufacturer.
1. Surface Preparation: Generally the following surface preparation can be used.
A. Thoroughly sand all enclosure surfaces with 180 grit sandpaper. If sanding marks
are objectionable, nish sanding with 220 or 240 grit sandpaper.
B. Wet wipe all surfaces with a solvent to remove any possible contaminants.
C. Apply two or three medium to light coats of paint. Allow two or three minutes
ash o between coats.
D. Allow paint to cure adequately. Consult with your paint manufacturer for proper
cure time and hardness prior to testing the paint for adhesion. Air dry enamels
may require signicantly longer cure times over some powders.
2. Paints to use: Various types of paint exhibit greater adhesion qualities than others
when applied over polyester powder. Below is a list of nishes that exhibit very good
adhesion properties.
• Two-component epoxies
• Some two-component polyurethanes
• Alkyd baking enamels
- To avoid discoloration of alkyd nishes do not bake at temperatures
exceeding 150°F.
NOTICE: Always test the repainting process on an inconspicuous area prior to use.
Produktspecifikationer
| Varumärke: | Hoffman |
| Kategori: | Inte kategoriserad |
| Modell: | A4044LP |
Behöver du hjälp?
Om du behöver hjälp med Hoffman A4044LP ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Hoffman Manualer
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
5 April 2025
Inte kategoriserad Manualer
- Cubot
- Fizzics
- Iget
- Zaahn
- PowerXL
- Hifonics
- Shuttle
- Datalogic
- Equator
- XS Power
- Ditek
- Ridem
- Teltonika
- On-Q
- Plant Craft
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025