Hoffman F88WP Bruksanvisning
Läs gratis den bruksanvisning för Hoffman F88WP (12 sidor) i kategorin Kablar för PC och kringutrustning. Guiden har ansetts hjälpsam av 59 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 30 recensioner. Har du en fråga om Hoffman F88WP eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/12
Feed Through Wireway−
Feed Through Kabelkanal−
Chemin de câbles grande étanchéité
Ducto De Vidrio Con Brida Cerrada
87565317
Rev. B 113357 P/N 99401616E 2005 Hoffman Enclosures Inc.
®
E 2005 Hoffman Enclosures Inc.
2 87565317
INDEX
INDEX
INCRÉMENT
ÍNDICE
CONTENT PAGES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INHALT SEITEN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENUE PAGES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENIDO PÁGINA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
English Instructions 3−5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deutsche Anleitung 6−8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instructions français 9−11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Español Instrucciones 12−14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
87565317 3
E 2005 Hoffman Enclosures Inc.
1ENGLISH
Installation Instructions
Feed−Through Wireway
I. FINISH: The standard finish on this wireway is gray polyester powder over a cleaned and phosphatized surface. This
surface may be further finished with lacquer or enamel.
II. ASSEMBLY: To assemble most wireway sections and
fittings, simply place a gasket between
flanges and install screws and nuts as
shown in detail 1.
III. TELESCOPE FITTING:
A. To Adjust Telescope Fitting:
1. Assemble parts on body of telescope fitting in correct order as shown in detail 2.
2. Insert body of telescope fitting into straight section and adjust to the desired length.
3. Position gasket retainer against flange of straight section and force the gasket inside the gasket retainer
and against the flange.
4. Position compression ring against gasket retainer and install screws and nuts as shown in detail 3.
5. If wireway is to be used as ground, provisions must be made for grounding continuity across telescope fitting.
B. To Anchor Telescope Fitting at Desired Extension:
1. If the telescope fitting is used in a vertical position to support the wireway above, or if the telescope fitting
is otherwise subjected to a material axial load, means to support such a load may be provided by one of
two methods:
Method I: With the telescope fitting at the desired
extension, drill .25 inch diameter holes through each
side of the straight section and through the
telescope fitting. Install .25 20x.5 screws through−
the holes from the outside and install cap nuts and
lockwashers as shown in detail 4.
Method II: Replace screws in two diagonally
opposite corners of flanges with .25−20 threaded
rods. Assemble rods, nuts, and washers as shown
in detail 5. After tightening the nuts, measure the
length of the extension to be sure it is the same on
both sides.
Flange Gasket
Wireway
Sections
Detail 1
Gasket
Detail 3
Gasket Retainer
Detail 2
Gasket
Compression Ring
Body
Straight Section
Detail 4
Straight Section
Anchoring Screws
Telescope Fitting
(Nuts and lockwashers
are on inside)
Detail 5
Telescope Fitting
Lockwashers
And Nuts
Straight
Section
.25−20 Threaded
Rods
Produktspecifikationer
| Varumärke: | Hoffman |
| Kategori: | Kablar för PC och kringutrustning |
| Modell: | F88WP |
Behöver du hjälp?
Om du behöver hjälp med Hoffman F88WP ställ en fråga nedan och andra användare kommer att svara dig
Kablar för PC och kringutrustning Hoffman Manualer
5 April 2025
5 April 2025
Kablar för PC och kringutrustning Manualer
Nyaste Kablar för PC och kringutrustning Manualer
9 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
3 April 2025
2 April 2025
2 April 2025
2 April 2025
