Honeywell Performance HBW4PGR1 Bruksanvisning
Sidor 3 Engels övervakningskamera
Läs bruksanvisningen för Honeywell Performance HBW4PGR1 gratis online eller ladda ner PDF:en. 32 personer har tyckt att guiden var hjälpsam. Fråga om modellen? Ställ en fråga
HBW4PGR1 WDR 4MP IR Bullet Camera
Quick Installation Guide
Thank you for purchasing a Honeywell Performance Series IP camera.
Follow the instructions in this guide to install and log in to your camera
For instructions on configuring the camera, refer to the user guide on t
CD that came with your camera. If you require additional assistance, ca
the number listed for your region on the back cover.
Cautions and Warnings
WARNINGTo ensure compliance with electrical safety standards, this product is
intended for use with a Listed Power Adapter marked “Limited Power
Source” or “LPS” on the unit, output rated to 12 VDC, minimum 0.33 A,
TMA=60 deg C, or from Power over Ethernet (PoE) provided by Listed
Information Technology Equipment meeting IEEE 802.3af PoE standard.
CAUTION
The Ethernet connection is not intended to be connected to exposed
(outside plant) networks. Do not connect two power sources to the camera
at the same time.
CAUTION
Invisible LED radiation (850 nm). Avoid exposure to beam.
Important Safeguards
•Read and keep these instructions.
•Confirm the installation surface can support at least three times the weight of the camera.
•Do not aim the camera toward a bright light source for extended periods to prevent damage to the imager.
•Avoid operating the unit under or close to unstable light sources (may cause flickering), or close to fluorescent
lamps or objects reflecting light.
•D o not touch the camera lens.
•Do not drop the camera or subject it to physical shock.
•Do not use a strong or abrasive detergent when cleaning the camera.
•Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments, where the operating
temperature is outside the recommended range of -22°F to 140°F (–3 0°C to 60°C).
•Do not apply power to the camera before completing installation.
Before You Begin
Before you begin, check that you have received all of the parts listed below. If any parts are missing or damaged,
contact your dealer immediately.
•Camera
•Installation CD
•Quick installation guide
•Allen key (L-wrench)
•
Self- tapping screws (×4)
•Plastic wall anchors (×4)
•Mounting template
CAUTIONInstallation and servicing should be performed only by qualified and experienced technicians to conform
to all local codes and to maintain your warranty.
Preparing the Mounting Surface
1.Apply the mounting template to the mounting surface.
Note Observe the orientation of the cable exit notch on the bracket base. In outdoor the notch installations,
should point downward to prevent water from entering the camera housing.
2.Using the mounting template as a guide, drill pilot holes in the mounting surface, then hammer the supplied four
anchors into the holes.
3.Drill a cable entry hole in the mounting surface, then pull the required cables through the hole.
Mounting and Aiming the Camera
1.If you are using a microSD card with the camera, install it before continuing. To access the microSD card slot,
remove the panel m mon the underside of the camera and insert a icroSD card into theicroSD card slot (refer to
the picture below).
Note Press and hold the reset button abouts 10s when the camera is power on or rebooting to restore the
default settings, including the user name, password, IP address, port NO., ect.
2.Connect one end of the Ethernet cable to the RJ-45 port on the
camera.
3.If the other end of the Ethernet cable is NOT connected to a PoE
switch or NVR, connect the power connector of the camera to a 12
VDC power source.
4.If the camera is installed outdoor, you can adapt the water- proof
accessory for the network cable after the camera is secured on the
installation surfacerefer to the picture (on the right).
5.Attach the camera assembly to the mounting surface using the
supplied screws.
CAUTION
THIS SYMBOL INDICATESTHAT
DANGE OUSRVOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
CA:TUTIONO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NT REMTHE COOVEOVER.
NO USER-SERVICEABLE PAR.TS INSIDE
REFER SERTOQURVICINGALIFIED SEVICE
PERSONNEL.
THIS SYMBOL INDICATESTHAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANYTHIS UNIT.
RISK OF ELECTRIC
SHOCK
DO NT OPENO
Produktspecifikationer
| Varumärke: | Honeywell |
| Kategori: | övervakningskamera |
| Modell: | Performance HBW4PGR1 |
Behöver du hjälp?
Om du behöver hjälp med Honeywell Performance HBW4PGR1 ställ en fråga nedan och andra användare kommer att svara dig
övervakningskamera Honeywell Manualer
Honeywell Lyric C1 Wi-fi Bruksanvisning Honeywell Equip HCD554IP Bruksanvisning Honeywell equIP H3D1F Bruksanvisning Honeywell Acuix HDVJNWAC Bruksanvisning Honeywell Performance HD262H Bruksanvisning Honeywell Performance HD273XD2 Bruksanvisning Honeywell HBD3PR2 Bruksanvisning Honeywell Performance H4W2PER2 Bruksanvisning
Alla Honeywell övervakningskamera manualer
Populära i övervakningskamera
Honeywell Equip HCD5WIH Bruksanvisning Honeywell HC35W45R3 Bruksanvisning Honeywell Performance HD31H Bruksanvisning
övervakningskamera Manualer
Nyaste övervakningskamera Manualer
Hanwha Vision PNM-8082VT Bruksanvisning Hanwha Vision TNO-7180RLP Bruksanvisning Hanwha Vision ANV-L7012R Bruksanvisning Hanwha Vision PND-A9081RV Bruksanvisning Hanwha Vision HCB-6001 Bruksanvisning Denver IIC-215MK3 Bruksanvisning Hanwha Vision HCO-6070R Bruksanvisning Hanwha Vision PNO-A9092R Bruksanvisning Hanwha Vision PNM-C9022RV Bruksanvisning Hanwha Vision ANO-L7022R Bruksanvisning