Hoselink Evolve Bruksanvisning


Läs gratis den bruksanvisning för Hoselink Evolve (2 sidor) i kategorin trädgårds slang. Guiden har ansetts hjälpsam av 22 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 11.5 recensioner. Har du en fråga om Hoselink Evolve eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Sida 1/2
Retractable Hose Reel
I N S T R U C T I O N M A N UA L
I N S TA L L AT I O N
Bracket into Masonry
1 Use the bracket as a template to
mark all four holes with a pencil,
using a spirit level to ensure it
is straight.
a 10mm masonry drill bit.
TIP: Use sticky tape around the
drill bit to mark 50mm depth.
Be sure to set the drill to the
‘Hammer’ setting.
3 Hammer the plugs into each hole.
4 Set the bracket in place, then
use the supplied 200mm Phillips
Head drill bit to loosely screw in
each screw.
5 Once all are in place, tighten
each screw.
For specific instructions on all
surface types, visit the Product
Support page at hoselink.com.au.
Bracket into Timber
1 Use the bracket as a template
to mark all four holes with a
pencil, using a spirit level to
ensure it is straight.
2 Drill four holes 50mm deep using
a 5mm drill bit.
TIP: Use sticky tape around the
drill bit to mark 50mm depth.
3 Set the bracket in place, then
use the supplied 200mm Phillips
Head drill bit to loosely screw in
each screw (plugs not required).
4 Once all are in place, tighten
each screw.
C O M P L E T E S E T U P
Place Hose Reel
onto the Bracket
C O M P L E T E S E T U P
Attach Stopper Ball
Troubleshooting
Visit the Product Support
section on our website
or scan the QR code for
more information.
2 Open the stopper ball
lever from the side
closest to the ‘K’.
3 Put the stopper ball
approximately 20cm
behind the connector.
Push with your palm
from the ‘H’ side to
latch the lever.
Connector and
Sprayer Assembly
1 Push the Hose Connector with
Flow Control Body onto the end
of the main hose. Secure by tightly
screwing in the pre-attached nut.
2 Screw the Accessory Connector
with Swivel into the Sprayer.
3 Attach the sprayer to the main hose.
To join Hoselink fittings, hold a fitting
in each hand, line up the lugs and use
a point and twist motion to connect.
4 Screw the Universal Tap
If the connector appears too small,
unscrew the size reducer and
screw the main connector body
onto the tap.
5 Connect the 2m Leader Hose onto
the Universal Tap Connector with the
same point and twist action.
2
3
1 4
3
Tilt the reel at an angle over
the top post rst to attach, then
level the reel to slide it onto the
bottom post. Do this in reverse
to remove it.
T I P
Complete this step without water
pressure in the hose.
1 Pull the hose out about half
a metre and lock the length.
If this is too difcult, extend
the hose to the ground. Put
your foot on the ‘H’ side and
roll the ball forward to latch
the lever.
T I P
R E A DY T O U S E
Specications
Model Hose Length Weight Weight Max working
with water pressure
E10020B 20m Internal 12.35kg 13.85kg 150psi
E10020C Hose + 2m
Leader Hose
E10030B 30m Internal 14.80kg 17.90kg 150psi
E10030C Hose + 2m
Leader Hose
Using the Hose Reel
1 To use the hose, simply pull it out to the
desired length. The hose will retract slightly
and lock at that length.
2 To commence retraction, gently pull the
hose to unlock, then allow it to retract
automatically as you walk it back in.
3 Always fully retract the hose after use.
Masonry
Installation
5
2
Size
Reducer


Produktspecifikationer

Varumärke: Hoselink
Kategori: trädgårds slang
Modell: Evolve

Behöver du hjälp?

Om du behöver hjälp med Hoselink Evolve ställ en fråga nedan och andra användare kommer att svara dig




trädgårds slang Hoselink Manualer

trädgårds slang Manualer

Nyaste trädgårds slang Manualer