Icom HM-162E Bruksanvisning

Läs gratis den bruksanvisning för Icom HM-162E (8 sidor) i kategorin mottagare. Guiden har ansetts hjälpsam av 23 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 7 recensioner. Har du en fråga om Icom HM-162E eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

INSTRUCTIONS

REMOTE-CONTROLMICROPHONE

HM-162E

Thank you for purchasing the HM-162E

REMOTE

-

CONTROLMICROPHONE

. The COMMANDMIC III

TM

is a

remote control microphone for use with the IC-M603

or else.

Please read the connected transceiver’s instruction

manual carefully before installation and operation.

These instructions are just described the remote-

control operations only.

qBUSY/TRANSMIT INDICATOR

➥“

BBUUSSYY

” appears when receiving a signal or when the

squelch opens.

➥“

TTXX

” appears while transmitting.

wRX SPEAKER INDICATOR

Appears during the RX speaker mode.

eSCRAMBLER INDICATOR

“

SSCCRRAAMM

” appears when an optional voice scrambler is acti-

vated.

rSCAN INDICATOR

➥“

PPRRII--SSCCAANN1166

” appears during Priority scan; “

NNOORR--

MMAALLSSCCAANN

” appears during Normal scan.

➥“

DDUUAALL1166

” appears during dualwatch; “

TTRRII1166

” ap-

pears during tri-watch.

tSELECTOR STATUS INDICATOR

Indicates the [SELECTOR]active status;

“

[[VVOOLL]]

” appears when [SELECTOR]functions as the

audio volume.

“

[[SSQQLL]]

” appears when [SELECTOR]functions as the

noise squelch controller.

“

[[DDIIAALL]]

” appears when [SELECTOR]functions as the

channel selector.

yPOSITION INDICATOR

➥Shows the GPS position data.

•“

????

” may blink every 2 sec. instead of position data when

the GPS position data is invalid. In this case, the last position

data is held for up to 23.5 hours.

•“

????

” may blink every 2 sec. instead of position data 4 hours

after the position data is input manually, up until 23.5 hours

have past.

➥“

NNooPPoossiittiioonn

” appears when no GPS receiver is con-

nected and no position data is input manually.

uTIME ZONE INDICATOR

➥“

LLooccaall

” appears when the offset time data in the ‘Set

up’menu is entered.

➥“

NNooTTiimmee

” appears when no GPS receiver is connected

and no time data is input manually.

iCHANNELCOMMENT INDICATOR

Channel comment appears, if programmed.

oCHANNELNUMBER READOUT

Indicates the selected operating channel number.

!0KEYLOCK INDICATOR

➥Appears while the Key Lock function is in use.

➥Blinks while the All Key Lock function is in use.

!1LOW BATTERYINDICATOR

“” blinks when the battery voltage drops to approx. 10V

DC or below.

!2CALLCHANNELINDICATOR

“

CCAALLLL

” appears when the call channel is selected.

!3CHANNELGROUPINDICATOR

Indicates whether an International “

IINNTT

,” U.S.A. “

UUSSAA

,”

DSC “

DDSSCC

” or ATIS “

AATTIISS

” channel is selected.

•Depending on the connected transceiver’s version.

!4DUPLEX INDICATOR

Appears when a duplex channel is selected.

•Duplex channel has a different TX and RX frequency.

!5TAG CHANNELINDICATOR

Appears when a tag channel is selected.

!6POWER INDICATOR

➥“

2255WW

” appears when high power is selected.

➥“

11WW

” appears when low power is selected.

BUSYBUSY-25W25W------INTINT------CALLCALL

LOC-LOC--- -- DUPDUP

SCRAMSCRAM--TAGTAG

NORMALNORMAL-SCANSCAN

-3434°34.506N34.506N

123123°23.236W23.236W

LocalLocal----1:101:10- - CALLINGCALLING

RXRX

[VOL]

q

w

e

y

u

r

t

!6!4!5!3!2

o

!0

!1

i

Accessories included with the HM-162E: Qty.

qConnection cable (OPC-1540*: 6m; 20 ft) .......................1

wMounting base ..................................................................1

eConnector cap ..................................................................1

rMicrophone hanger ..........................................................1

tScrews (M3 ×16; tapping) ...............................................5

*: OPC 1540 has external speaker leads as illustrated at right.

(Yellow: Audio, Black: Speaker ground)

Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Rus-

sia and/or other countries. COMMANDMIC III is a trademark of Icom Incorporated (Japan) in the United states.

These instructions are described when the HM-162E is connected to the IC-M603. Some operations or indications may be dif-

ferent as these instructions depending on the connecting transceiver.

xFunction display

zHM-162E supplied accessories

qwe

r

t

Yellow

Black

1

Produktspecifikationer