IFM ZZ0057 Bruksanvisning
IFM
Inte kategoriserad
ZZ0057
Läs gratis den bruksanvisning för IFM ZZ0057 (7 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 2 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 1.5 recensioner. Har du en fråga om IFM ZZ0057 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/7
Short instructions
Cooling water control panel
ZZ0057
701720 12 / 2018
UK
2
1 System description
7
KWST
ZZ0057
3
4
water out
12
water in
65
Mode
/Enter
Set
SP1
SP2
°F
°C
gph
gpm
m3/h
l/min
7
1 Filter Filters solids to avoid clogging / damage to the system.
2 Flow sensor Monitors and indicates the cooling water flow rate.
The setting of two switch points enables detection of:
• excess flow (leakage / burst pipes / lost tips)
• low flow (clogged / damaged pipes)
3 Water stop
valve
Closes the water supply to the system in case of failure and
prevents water spillage.
4 Backstop Prevents cooling water loss through the return pipe in case
of failure (broken tip / burst pipe).
3
DE
5 Regulating
valve
Regulation of the flow rate.
Adjustable in 6 steps, preset: step 3.
6 Pressure
sensor
Monitors the operating pressures, very fast response times
are attained if pressure falls (broken tips).
7 Cover Protection against mechanical damage.
2 Functions and features
Pressure Equipment Directive (PED)
The units comply with the Pressure Equipment Directive and are designed
and manufactured for group 2 fluids in accordance with the sound engineering
practice.
Use of group 1 fluids on request.
3 Setting of the flow sensor
The flow sensor monitors the flow rate in the supply pipe by means of a window
function. This is achieved by setting the output function of the two outputs:
OU1 and OU2 = Fno, window / normally open.
With this setting an acceptable range is monitored.
The flow rate depends on the water supply and the set-up of the welding tongs.
The setting of the switch-on points (SP1, SP2) and the switch-off points (rP1, rP2)
depends on the installation.
Optimum monitoring of the start up characteristics as well as processrelated flow
fluctuations during operation is possible via additional monitoring times in the
robot software.
Produktspecifikationer
| Varumärke: | IFM |
| Kategori: | Inte kategoriserad |
| Modell: | ZZ0057 |
Behöver du hjälp?
Om du behöver hjälp med IFM ZZ0057 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad IFM Manualer
8 April 2025
8 April 2025
8 April 2025
2 April 2025
2 April 2025
1 April 2025
1 April 2025
1 April 2025
31 Mars 2025
12 Mars 2025
Inte kategoriserad Manualer
- Sweex
- BBE
- Bavaria By Einhell
- Steelton
- NUX
- Mobotix
- Bosch
- Crystal Video
- Café
- Marvel
- Inter-Tech
- Velleman
- Valeton
- Scanstrut
- Dynon Avionics
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025