Ignis AKL 805 Bruksanvisning

Ignis Ugn AKL 805

Läs gratis den bruksanvisning för Ignis AKL 805 (6 sidor) i kategorin Ugn. Guiden har ansetts hjälpsam av 6 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 3.5 recensioner. Har du en fråga om Ignis AKL 805 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Sida 1/6
9
CONTENTS GB
BEFORE USING THE GLASS CERAMIC HOB
PAGE
10
INSTALLATION
PAGE
10
ELECTRICAL CONNECTION
PAGE
11
PAGE
12
PROTECTING THE ENVIRONMENT
PAGE
12
DECLARATION OF CONFORMITY CE
PAGE
12
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
PAGE
12
COOKTOP ACCESSORIES
PAGE
13
CARE AND MAINTENANCE OF THE
GLASS-CERAMIC COOKTOP
PAGE
13
TROUBLESHOOTING GUIDE
PAGE
13
AFTER SALES SERVICE
PAGE
14
1gb59055.fm5 Page 9 Monday, November 11, 2002 6:54 PM
10
To make the most of your new appliances read the
users instructions carefully and keep them on
hand for consultation in the future.
Cooktop
The cooktop must be set into a worktop
between 20 mm and 50 mm thick. There must
be nothing between the cooktop and the oven
(cross rails, brackets, etc.).
If the cooktop is to be installed next to a
column unit, leave a distance of at least
100 mm from the edge of the cooktop to the
side of the column unit.
Cut an opening in the worktop of the dimensions
shown in the Product Description Sheet supplied
separately.
N.B.: Remove the protective film before installing the
cooktop.
If the worktop is made of wood, use the supplied
spring clips and screws.
1. Position the 4 clips (D) as shown and at the
specified dimensions
2. Secure the clips using screws (E).
3. Fit the cooktop into the worktop.
If the worktop is made of marble, ceramics,
natural stone, etc., the cooktop must be secured
with brackets (F) code 4819 404 78697 (to be
requested from After-Sales Service).
1. Fit the cooktop into the worktop.
2. Position the 4 brackets (F) as shown in the figure,
in accordance with the thickness of the worktop.
3. Fix the 4 screws (G) in holes (H).
BEFORE USING THE GLASS CERAMIC HOB
INSTALLATION
1gb59055.fm5 Page 10 Monday, November 11, 2002 6:54 PM
11
Make sure the appliance is installed and
connected to the electricity supply by a
qualified technician in accordance with
the manufacturer’s instructions and in
compliance with local regulations.
The installer is responsible for the correct
electrical connection of the appliance and
the observance of the relative safety
prescriptions.
The appliance must be connected to the
electricity supply by means of an all-pole
disconnect switch with minimum contact
gap of 3 mm.
The appliance must be earthed by law.
Do not use multiple plug adapters or
extension leads.
After the appliance has been installed, the
electrical components must be inaccessible.
No liability for damage or injury to
persons or property will be accepted from
non-observance of these requirements.
CONNECTION AND INSTALLATION
If the cooktop terminals do not correspond to the
connection and colour indications on the
cooktop/oven connection plate located at the top
of the oven, request the adaptor kit,
code AMC 874, from the After-sales Service.
1. Install the cooktop in its seat.
2. Connect the four terminals A to the oven
terminals B situated in the rear section,
paying attention that the correspondance of
the coloured plugs is respected.
3. Fasten the cooktop.
4. Install the oven and fix it with the screws
supplied.
Note
If the cooktop must be connected to the separate
control panel instead of the oven read the
instructions supplied with the control panel.
ELECTRICAL CONNECTION
1gb59055.fm5 Page 11 Monday, November 11, 2002 6:54 PM

Produktspecifikationer

Varumärke: Ignis
Kategori: Ugn
Modell: AKL 805

Behöver du hjälp?

Om du behöver hjälp med Ignis AKL 805 ställ en fråga nedan och andra användare kommer att svara dig