Inovonics EN1262 Bruksanvisning
Inovonics
Rörelsedetektor
EN1262
Läs gratis den bruksanvisning för Inovonics EN1262 (3 sidor) i kategorin Rörelsedetektor. Guiden har ansetts hjälpsam av 25 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 13 recensioner. Har du en fråga om Inovonics EN1262 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/3
1.23.14 05469E © Inovonics, 2014 - www.inovonics.com
EN1262 EchoStream® Passive Infrared Motion
Detector
Installation and Operation Manual
1 Overview
The EN1262 is a low-current motion detector highly sensitive to moving
heat (infrared radiation) sources.
1.1 Inovonics Contact Information
If you have any problems with this procedure, contact Inovonics technical
services:
• E-mail: support@inovonics.com
• Phone: (800) 782-2709; (303) 939-9336
1.2 What’s in the Carton
• One Duracell DL123A 3.0V battery
• Two selection jumpers
• Two mounting drywall anchors
• Two mounting screws
• Two housing screws
• One tamper wall anchor
• One tamper rivet
1.3 Passive Infrared Motion Detector Internal
Components
Figure 1 EN1262 Components
2 Installation and Startup
2.1 Installation Notes
• These products are designed to be maintained by professional
security technicians
• Products are tested for indoor use
• All products should be manually tested weekly
2.2 Mount the Housing
1. Insert a small at-blade screwdriver at the tab on the bottom of the unit.
The screwdriver will enter the slot at about a 45° angle. Press
downward on the handle of the screwdriver until the latch holding the
cover to the housing base releases.
Figure 2 Open the housing
2. Pull the circuit board attachment latch and lift the circuit board out of the
housing.
Figure 3 Circuit board attachment latch
3. As desired install the wall tamper rivet.
Note: Wall tamper installation is required for BSI Class VI.
a. Use a 3/16” (4.8mm) bit to drill out the tamper rivet hole index.
b. Install the tamper wall anchor in the wall where you will be mounting
the motion detector’s tamper rivet.
c. Use a hammer to tap a rivet into place in the tamper wall anchor.
Figure 4 Mounting hole indices
AWall tamper
selection pins
BHousing tamper
switch
CFrequency band
selection pin
DReset button
C
A
B
D
ATamper rivet index BCorner mount index CWall mount index
Circuit board
attachment
latch
A
BB
B
B
C
B
B
C
C
Produktspecifikationer
| Varumärke: | Inovonics |
| Kategori: | Rörelsedetektor |
| Modell: | EN1262 |
Behöver du hjälp?
Om du behöver hjälp med Inovonics EN1262 ställ en fråga nedan och andra användare kommer att svara dig
Rörelsedetektor Inovonics Manualer
24 September 2024
24 September 2024
10 September 2024
9 September 2024
Rörelsedetektor Manualer
- Chacon
- Lucide
- Fibaro
- Honeywell
- Gira
- Brinno
- Pepperl+Fuchs
- InLine
- Massive
- EtiamPro
- Dahua Technology
- Busch-Jaeger
- Crestron
- Schwaiger
- EQ3
Nyaste Rörelsedetektor Manualer
8 April 2025
8 April 2025
5 April 2025
1 April 2025
1 April 2025
1 April 2025
1 April 2025
27 Mars 2025
27 Mars 2025
5 Mars 2025