JennAir JUR24FLARS Bruksanvisning
Läs gratis den bruksanvisning för JennAir JUR24FLARS (4 sidor) i kategorin kylskåp. Guiden har ansetts hjälpsam av 9 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 5 recensioner. Har du en fråga om JennAir JUR24FLARS eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
HANDLE AND BRAND BADGE INSTALLATION
Once the undercounter appliance has been completely installed, follow these instructions to
replace the factory installed handle and badge with the handle and badge in this kit.
Parts and Tools Included:
Tools Needed:
Replace Handle
NOTES:
■To avoid scratching the door, place a soft cloth against the door while removing the
factory installed handle and installing the alternative handle.
■Save the hex key and all instructions.
1. Remove the hex key wrench from the hardware bag.
2. While holding the handle, insert the short end of the hex key into a hole in the underside of
the handle. Using a right to left motion, loosen the setscrew. ❶
3. Repeat steps 1 and 2 to loosen the second setscrew. Pull the handle away from the door
or drawer.
4. With the setscrews facing down, place the new handle on the mounting studs so that the
base of the handle is flush against the front panel.
5. Insert the short end of the hex key into the handle to engage the setscrew. Using a left to
right motion, tighten the setscrew. ❷
6. Repeat steps 3 and 4 to fasten the second setscrew. When the screws feel tight, tighten
them an additional quarter-turn.
Replace Brand Badge
1. Using the tool (provided), lift up the right-hand side of the badge and peel it from right to
left away from the door.
NOTE: To avoid scratching the door, do not use a sharp or metallic object to pry the
brand badge from the door.
2. Rub a small amount of liquid dish soap over any adhesive residue with your fingers. Rinse
the door with warm water and dry with a soft cloth.
3. Cut the template along the dotted lines that match the shape of the brand badge.
4. Align the edges of the template with the bottom and right-hand side edges of the door.
Tape the template to the door. Remove the tape from the back of the brand badge. ❸
5. Using the cutout as a guide, press the brand badge onto the door making sure the hole is
completely covered. Remove the template.
A
B
C
D
A
B
C
D
A. Mounting stud
Perno de montaje
Goujon de montage
B. Door handle
Manija de la puerta
Poignée de porte
C. Setscrew (inside handle standoff)
Tornillo opresor (en el interior del soporte de la manija
Vis de blocage (à l'intérieur du pied de la poignée)
D. Hex key
Llave hexagonal
Clé à tête hexagonale
❷❶ ❸
W10586889A
■Handle
■Extra setscrew
■Brand badge template (last page of
instructions)
■Brand badge
■Brand badge removal tool
■Hex key wrench
■ ■Masking tape Scissors
Produktspecifikationer
| Varumärke: | JennAir |
| Kategori: | kylskåp |
| Modell: | JUR24FLARS |
Behöver du hjälp?
Om du behöver hjälp med JennAir JUR24FLARS ställ en fråga nedan och andra användare kommer att svara dig
kylskåp JennAir Manualer
8 Januari 2025
8 Januari 2025
7 Januari 2025
7 Januari 2025
7 Januari 2025
27 Oktober 2024
27 Oktober 2024
22 September 2024
22 September 2024
22 September 2024
kylskåp Manualer
- Blucher
- Severin
- V-Zug
- Sam Cook
- Thor
- Edy
- Chefman
- Leonard
- Upo
- Gaggenau
- Kenwood
- Heller
- Flavel
- Guzzanti
- Freggia
Nyaste kylskåp Manualer
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
23 Oktober 2025
21 Oktober 2025
21 Oktober 2025
20 Oktober 2025
20 Oktober 2025