Jensen VM9214BT Bruksanvisning

Jensen DVD-spelare VM9214BT

Läs nedan 📖 manual på svenska för Jensen VM9214BT (12 sidor) i kategorin DVD-spelare. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/12
1
VM9214BT
VM9214BT Head Unit
Single DIN Sleeve
Wiring Harness
Parking Brake Sensor Extension Wire
Mounting Hardware
Cosmetic Trim Ring
3.5mm to 3.5mm Media Adaptor Cable
Owners Manual
Installation Guide
What’s in the Box
You will need these tools and supplies to install your VM9214BT:
• Torx type, fl at-head and Philips screwdrivers
• Wire cutters and strippers
• Tools to remove existing radio (screwdriver, socket wrench set or other tools)
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 18 gauge wire for power connections
• 16 – 18 gauge speaker wire
Tools and Supplies
Installation Guide
Instruccionnes de Instalación
Instructions d’installation
WARNING! Never install this unit where operation and viewing could interfere with safe driving
conditions.
Para obtener instrucciones en Español, diríjase a la página 5. Pour des instructions en Francais, référez-vous à la page 9.
EJECT
A / V
INPUT
VM9214BT
DISP
M
U
T
E
2
TAB
DASHBOARD
DASHBOARD
TAB
Optional Equipment
• NAV102: Allows you to access navigation features. All installation and operating instructions are included
with the navigation module.
• Rear Camera
Disconnecting the Battery
To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to in-
stallation.
NOTE: If the VM9214BT is to be installed in a car equipped with an on-board drive or navigation computer, do
not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these
conditions, use extra caution during installation to avoid causing a short circuit.
Pre-installation
Remove the four screws that attach the mounting sleeve to the
radio and remove the sleeve.
Install the mounting sleeve.
a. Install mounting sleeve into the dashboard or optional
adapter. Do not force the sleeve into the opening or cause
it to bend or bow.
b. Locate the series of bend-tabs along the top, bottom and
sides of the mounting sleeve. With the sleeve fully insert-
ed into the dashboard opening, bend as many of the tabs
outward as necessary so that the sleeve is fi rmly secured
to the dashboard.
c. Install support strap to make the unit more stable.
Place the radio in front of the dashboard opening so the wiring
can be brought through the mounting sleeve.
CAUTION! Be careful not to damage the car wiring.
1
2
3
3
Wiring
WARNING! Only connect the unit to a 12-volt power supply with proper grounding.
Complete wiring as illustrated in the wiring diagram on page 4. Once the wiring is complete, reconnect the bat-
tery negative terminal. If there is no ACC available, connect the ACC lead to the power supply with a switch.
NOTE: When replacing a fuse, be sure to use correct type and amperage to avoid damaging the radio. The
VM9214BT uses one 15 amp fuse, located in the black fi lter box in-line with the main wire harness.
Final Installation
After completing the wiring connections, turn the unit on to confi rm operation (ignition switch must be on). If
unit does not operate, recheck all wiring until problem is corrected. Once proper operation is achieved, turn off
the ignition switch and proceed with fi nal mounting of the chassis.
Connect wiring adapter to existing wiring harness.
Connect antenna lead.
Carefully slide the radio into the mounting sleeve, making
sure it is right-side-up, and secure with the original 4 screws.
Attach one end of the perforated support strap (supplied) to
the screw stud, which is screwed into the threaded insert on
the back of the unit, using the hex nut provided. Fasten the
other end of the perforated strap to a secure part of the
dashboard either above or below the radio using the screw
and hex nut provided. Bend the strap to position it as
necessary.
Replace any items you removed from the dashboard.
ISO-DIN Installation
Remove mounting sleeve brackets.
Remove trim ring.
Mount factory brackets on new radio using existing screws
from old radio.
Slide radio chassis into dash opening and secure.
Re-install dash panel.
EJE
CT
A/V
INPUT
EJE C
T
A/
VIN
PU T
1
2
3
4
5
1
2
3
4
5
CAUTION! The rear of the radio must be
supported with the strap to prevent dam-
age to the dashboard from the weight of
the radio or improper operation due to
vibration.
NOTE: For proper operation of the CD/
DVD player, the chassis must be mounted
within 20° of horizontal. Make sure the unit
is mounted within this limitation.
Remove Mounting
Sleeve Brackets
EJE C
T
A/ V
INPU T

Produktspecifikationer

Varumärke: Jensen
Kategori: DVD-spelare
Modell: VM9214BT

Behöver du hjälp?

Om du behöver hjälp med Jensen VM9214BT ställ en fråga nedan och andra användare kommer att svara dig


DVD-spelare Jensen Manualer

Jensen

Jensen CDR5620 Bruksanvisning

19 September 2024
Jensen

Jensen CDR7011 Bruksanvisning

16 Augusti 2024
Jensen

Jensen VM9214BT Bruksanvisning

11 Augusti 2024
Jensen

Jensen VM9424 Bruksanvisning

9 Augusti 2024

DVD-spelare Manualer

Nyaste DVD-spelare Manualer

Philips

Philips PET700 Bruksanvisning

5 April 2025
Salora

Salora DVP9018SW Bruksanvisning

3 April 2025
Blaupunkt

Blaupunkt IVOD-1022 Bruksanvisning

1 April 2025
Proscan

Proscan PDVD1046_FD Bruksanvisning

10 Mars 2025
Proscan

Proscan PDVD6655-B Bruksanvisning

10 Mars 2025
Proscan

Proscan PDVD1041 Bruksanvisning

10 Mars 2025
Proscan

Proscan PDVD6670 Bruksanvisning

10 Mars 2025
Samsung

Samsung DVD-HD746 Bruksanvisning

24 Februari 2025
Naxa

Naxa ND-837 Bruksanvisning

29 Januari 2025
Sony

Sony RDR-GXD455 Bruksanvisning

27 Januari 2025