JET JWP-13BT Bruksanvisning
JET
ej kategoriserat
JWP-13BT
Läs gratis den bruksanvisning för JET JWP-13BT (28 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 2 recensioner. Har du en fråga om JET JWP-13BT eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/28
1
Operating Instructions and Parts Manual
13-inch Portable Thickness Planer
Model JWP-13BT
JET
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-722130
Ph.: 800-274-6848 Edition 2 08/2019
www.jettools.com Copyright © 2018 JET
This .pdf document is bookmarked
2
1.0 IMPORTANT SAFETY
INSTRUCTIONS
WARNING – To reduce risk of injury:
1.1 General machine safety rules
1. Read and understand the entire owner's
manual before attempting assembly or
operation.
2. Read and understand the warnings posted on
the machine and in this manual. Failure to
comply with all of these warnings may cause
serious injury.
3. Replace the warning labels if they become
obscured or removed.
4. This planer is designed and intended for use by
properly trained and experienced personnel
only. If you are not familiar with the proper and
safe operation of a planer, do not use until
proper training and knowledge have been
obtained.
5. Do not use this machine for other than its
intended use. If used for other purposes, JET
disclaims any real or implied warranty and holds
itself harmless from any injury that may result
from that use.
6. Always wear ANSI Z87.1 approved safety
glasses or face shield while using this machine.
(Everyday eyeglasses only have impact
resistant lenses; they are not safety glasses.)
7. Before operating this machine, remove tie,
rings, watches and other jewelry, and roll
sleeves up past the elbows. Do not wear loose
clothing. Confine long hair. Non-slip footwear or
anti-skid floor strips are recommended. Do not
wear gloves.
8. Wear ear protectors (plugs or muffs) during
extended periods of operation.
9. Make certain the switch is in the OFF position
before connecting the machine to the power
supply.
10. Make certain the machine is properly grounded.
11. Make all machine adjustments or maintenance
with the machine unplugged from the power
source.
12. Remove adjusting keys and wrenches. Form a
habit of checking to see that keys and adjusting
wrenches are removed from the machine
before turning it on.
13. Keep safety guards in place at all times when
the machine is in use. If removed for
maintenance purposes, use extreme caution
and replace the guards immediately after
completion of maintenance.
14. Check damaged parts. Before further use of the
machine, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or
replaced.
15. Provide for adequate space surrounding work
area and non-glare, overhead lighting.
16. Keep the floor around the machine clean and
free of scrap material, oil and grease.
17. Keep visitors a safe distance from the work
area. Keep children away.
18. Make your workshop child proof with padlocks,
master switches or by removing starter keys.
19. Give your work undivided attention. Looking
around, carrying on a conversation and “horse-
play” are careless acts that can result in serious
injury.
20. Maintain a balanced stance at all times so that
you do not fall into the blade or other moving
parts. Do not overreach or use excessive force
to perform any machine operation.
21. Use the right tool at the correct speed and feed
rate. Do not force a tool or attachment to do a
job for which it was not designed. The right tool
will do the job better and more safely.
22. Use recommended accessories; improper
accessories may be hazardous.
23. Maintain tools with care. Keep blades sharp and
clean for the best and safest performance.
Follow instructions for lubricating and changing
accessories.
24. Turn off the machine before cleaning. Use a
brush or compressed air to remove chips or
debris — do not use bare hands.
25. Do not stand on the machine. Serious injury
could occur if the machine tips over.
26. Never leave the machine running unattended.
Turn the power off and do not leave the
machine until it comes to a complete stop.
27. Remove loose items and unnecessary work
pieces from the area before starting the
machine.
Produktspecifikationer
| Varumärke: | JET |
| Kategori: | ej kategoriserat |
| Modell: | JWP-13BT |
Behöver du hjälp?
Om du behöver hjälp med JET JWP-13BT ställ en fråga nedan och andra användare kommer att svara dig
ej kategoriserat JET Manualer
9 Oktober 2025
9 Oktober 2025
ej kategoriserat Manualer
- Chameleon Labs
- M-Live
- JMAZ
- Ignition
- MikroElektronika
- Hilti
- Apantac
- Oceanic
- Powr-Flite
- Petsafe
- Showtec
- BlueBuilt
- Ninja
- HyperX
- Kaiser
Nyaste ej kategoriserat Manualer
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025
10 Oktober 2025