Kenwood Excelon CA-PLT14SG Bruksanvisning
Kenwood
Inte kategoriserad
Excelon CA-PLT14SG
Läs gratis den bruksanvisning för Kenwood Excelon CA-PLT14SG (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 15 personer och har ett genomsnittsbetyg på 4.7 stjärnor baserat på 8 recensioner. Har du en fråga om Kenwood Excelon CA-PLT14SG eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new product.
© 2023 JVCKENWOOD Corporation
CA-PLT14SG
AMPLIFIER MOUNTING PLATE DESIGNED AND ENGINEERED FOR
2014-UP HARLEY-DAVIDSON® STREET GLIDE®, ULTRA, OR ULTRA TRIKE
MOTORCYCLES
INSTRUCTION MANUAL
JVCKENWOOD Corporation
Important Notes
©2023 JVCKENWOOD Corporation. All Rights Reserved. KENWOOD® and eXcelon®
are registered trademarks of JVCKENWOOD Corporation. Harley-Davidson®, Electra
Glide®, Road Glide®, Street Glide®, Ultra Classic®, Tri Glide®, CVO™, Screamin Eagle®
and Tour-Pak® are trademarks or registered trademarks of Harley-Davidson, Inc. and/
or its affiliates and if used or implied are for reference only. There is no affiliation
between Harley-Davidson, Inc. and/or its aliates and JVCKENWOOD Corporation
and/or its aliates. All other trademarks are the property of their respective owners.
Specications subject to change without notice.
The CA-PLT14SG plate is made to mount ampliers
with a maximum dimension of 8.5” W x 7” D x 2” H
(216mm x 178mm x 51mm).
Installation procedure
1. Over the top of the radio, pull up to release each wire harness from the black plate
via the factory “Christmas tree” fasteners. If your bike has factory GPS, the small square
antenna will need to be relocated just behind the voltmeter as shown in Fig 1.1 below.
Figure 1.1 - The white circle shows the new location for the GPS Antenna if your bike
came factory equipped with this feature.
2. Remove the four factory T-20 “Torx” screws that go through the top of the black plate
and into the top of the radio. Set these screws aside for now.
3. Sit the main amplier plate over the top of the radio, noting the 4 holes in the plate will
line up with the 4 holes left by the factory screws just removed. The factory screws will
now go through the main mounting plate, through the black plate over the top of the
radio, and into the top of the radio.
4. Locate the Velcro® that came in the box and stick it to the bottom plate of the amp
being installed. You can now “stick” the amp to the mounting plate just installed.
Depending on the amp you are installing, you can use the “tabs” on the CA-PLT14SG to
re-secure the wire harnesses that were held in place using the “Christmas Tree Fasteners.”
For updated information (the latest Instruction Manual, etc.),
please visit the following website:
https://manual.kenwood.com/en_contents/search/
Produktspecifikationer
| Varumärke: | Kenwood |
| Kategori: | Inte kategoriserad |
| Modell: | Excelon CA-PLT14SG |
Behöver du hjälp?
Om du behöver hjälp med Kenwood Excelon CA-PLT14SG ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Kenwood Manualer
23 Februari 2025
22 Februari 2025
22 Februari 2025
8 Januari 2025
9 December 2024
9 December 2024
27 Oktober 2024
24 September 2024
24 September 2024
21 September 2024
Inte kategoriserad Manualer
- Interlogix
- Hecht
- Quigg
- VARI-LITE
- Hasselblad
- FSR
- Gram
- Bolt
- Eurom
- Blustream
- Plant Craft
- Schaudt
- Epson
- Cherub
- Lexicon
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025