Kicker 46HDTPH Bruksanvisning
Kicker
hi-fi system
46HDTPH
Läs gratis den bruksanvisning för Kicker 46HDTPH (6 sidor) i kategorin hi-fi system. Guiden har ansetts hjälpsam av 24 personer och har ett genomsnittsbetyg på 4.8 stjärnor baserat på 12.5 recensioner. Har du en fråga om Kicker 46HDTPH eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/6
1. Remove the fairing, tank, and seat according to the manufacturer’s service manual.
2. Plug the 4-pin connector into the front kit’s rear
inputs, then route the RH14HDT harness through the
neck and wiring track to the rear of the bike .
3. Route the harness along the clutch side to the rear pods; notice the tags for the
clutch side and the throttle side.
4. Find the rear speaker 4-pin plug and unplug the resistor pack.
46HDTPH
Tour-Pak Harness Kit Installation Guide for
Harley Davidson® Tour-Pak Motorcycles 2014–Present
Package Contents:
(1) Install Guide (1) Wiring Harness RH14HDT (1) Wiring Harness RH14HDTI
(6) Zip Ties (4) Black Heat Shrink
Important: Over-tightening mounting fasteners may result in damage to your motorcycle. Please refer to your service
manual for proper procedures and torque specifi cations. KICKER is not responsible for damage resulting from improper
installation techniques. This kit be compatible with some aftermarket head units.may not
NOTE: It is necessary to re-fl ash your HD radio for 4 speaker set up before installation of this kit. If you do not have the
Techno Research Centurion program software you may purchase a Kicker TRHDP Radio Flash Programmer.
KICKER cannot be held responsible for any damage to painted surfaces during removal or addition of KICKER parts. 46HDTPH-B-20200305
5. Plug in the Rear accessory harness and route the harness along
the clutch side of the bike, alongside the factory harness.
6. Remove the factory speakers.
7. Route both side speaker wires (input
and output) through the factory gromet into
the speaker pod.
8. Connect the speaker wires to the factory or replacement speaker and connect the
input wires to the factory speaker wires. Use shrink wrap over the connections to factory
speaker wires to avoid shorts.
9. Reinstall the speakers and zip tie the
new harness to the factory harness, making
sure the new wiring does not interfere with
the seat.
10. Reinstall the tank, seat, and fairing.
NOTE: It will be necessary to check that the crossover and gains are set properly for the rear speakers if
you’re using factory or Kicker PS65 speakers. The crossover should be set to 80HZ with optimized gain lev-
els. For questions, please contact KICKER Technical Support at 800-256-0808, M-F 8:00am – 5:00pm CST
or email at support@kicker.com. For installation videos please go to our KICKER YouTube channel.
Package Contents:
(1)
Programmer Module
(1)
USB cable
NOTE
1:
MUST
BE
CONNECTED TO THE INTERNET
NOTE
2:
For motorcycles with:
Stock ECM: Follow the provided instructions below.
(1)
Diagnostic cable
(1)
Instructions
Power Commander: Disconnect the Power Commander from the the ECM circuit. Reconnect ECM to the stock
harness plug and then follow the provided instructions below.
Any Aftermarket ECM: Disconnect your your attermarket ECMand install stock ECMto the the bike harness. Follow
provided instructions below.
(For
some ECMs this
will
mean reinitializing the attermarket ECM when
it
is
reinstalled)
INSTALLING THE SOFTWARE FOR A FIRST TIME USER
1.
Download software program from http://technoresearch.com/index.php/support/downloads
2.
Once the download completes,
Run
software installer.
3.
If
using the Kicker TRHDP connect to your computer using the supplied USB cable.
4.
From the the Icon on your desktop, Start Centurion software.
5.
Allow software to update, accept terms and and conditions select language to launch program.
PROGRAMMING LIKE A PRO
1.
Remove side cover from left side of bike and locate the bottom 6-pin diagnostic plug.
2.
Connect your programmer to this plug.
3.
Turn
ignition switch to the Accessory position.
4.
Launch program
5.
To
connect to the the bike, select icon with two arrows facing each other
6.
Once connected to the the the bike, select icon with Wrench on
it
7.
You
will
now see a . drop-down menu From this menu, you can read and reset DTC's, and complete programing for
adding
KICKER
Audio upgrade kits.
2 SPEAKER FRONT KIT
1.
Select Radio speaker programing
2.
Select 2 Speakers- Front Speaker
Kit
3.
Select Program Speaker
a.
Follow on-screen directions, complete and look for Pass on the menu
4. Select from the drop-down menu: Radio Front Rear amp
5.
Select Front and Start
a.
Click enable and flash
b.
Follow the on-screen directions (confirm Pass)
6.
Exit
the rrogram
Produktspecifikationer
| Varumärke: | Kicker |
| Kategori: | hi-fi system |
| Modell: | 46HDTPH |
Behöver du hjälp?
Om du behöver hjälp med Kicker 46HDTPH ställ en fråga nedan och andra användare kommer att svara dig
hi-fi system Kicker Manualer
7 Oktober 2024
23 September 2024
10 September 2024
24 Augusti 2024
24 Augusti 2024
19 Augusti 2024
19 Augusti 2024
16 Augusti 2024
16 Augusti 2024
15 Augusti 2024
hi-fi system Manualer
Nyaste hi-fi system Manualer
15 Juni 2025
14 Juni 2025
14 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
10 Juni 2025
10 Juni 2025