Kicker 50HDR154 Bruksanvisning
Kicker
Inte kategoriserad
50HDR154
Läs gratis den bruksanvisning för Kicker 50HDR154 (2 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 21 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 11 recensioner. Har du en fråga om Kicker 50HDR154 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
1.
Remove the seat and disconnect both positive and negative battery terminals.
2.
Remove the windshield and outer fairing.
a.
Once the windshield screws are removed, gently pull off the top vent/cowl piece. There are two plastic retainer clips that hold it on.
b.
Remove your stock speaker grilles. Push them out from the inside of the fairing. They are fastened with a plastic retainer clip. Fig 1.
c.
Unplug the turn signals. Fig 2.
d.
Remove the lower T25 fasteners holding the air defl ectors to the inner fairing. Fig 3.
e.
Remove the 3/16” allen bolts holding the turn signals to the inner fairing. Fig 4.
f.
While holding the fairing, carefully remove the two T30 bolts behind the speaker grilles to remove the outer fairing and set aside. Fig 5.
3.
Remove the fuel tank.
a.
Remove the console.
b.
Unplug the fuel fi tting on the left side of the tank.
c.
Remove all four T40 mounting bolts and carefully lift the tank off the bike and set aside.
4.
Remove wiring caddy cover.
a.
Carefully release each tab along the caddy until it lifts completely. Fig 6.
SPEAKER INSTALLATION
5.
Remove your stock speakers and replace them with your new PSC652 speakers in the kit.
a.
Install the speaker into the pod and fasten with the original speaker screws. Fig 7.
50HDR154
Motorcycle Audio Kit Installation Guide for
Harley Davidson
®
Road Glide (FLTR) 2015–Newer
Package Contents:
(1)
Install Guide
(2)
PSC652 KICKER Speakers
(1)
Wiring Harness
(2)
8-32 x 1/2” Button Head Bolts
(1) KPX3004 KICKER Amp
(2) 8-32 Nylock Nuts
(6) Black Cable Ties
(1) Amplifier Mounting Bracket
Important: Over-tightening mounting fasteners may result in damage to your motorcycle. Please refer to your service manual for proper
procedures and torque specifi cations. KICKER is not responsible for damage resulting from improper installation techniques. This kit
may not
be compatible with some aftermarket head units.
PROGRAMMING HD RADIO
NOTE: It is necessary to re-flash your HD radio before installation of this kit.
GETTING STARTED
HARNESS INSTALLATION
6.
Route speaker wires to their respective connectors. Fig. 2
a.
Separate the speaker connectors and plug in the amplifier harness to each speaker. Fig. 8 & Fig. 8a
7.
Plug the switched power harness into the 2-pin amp connector on the throttle side. Fig. 9 (see also, Fig. 2 for location)
8.
Plug the blue wire on the kicker harness into the switched power harness lead with one wire. Fig. 9
a.
This allows for an accessory 12V port to remain available.
9.
Route both power leads and rear speaker output plug along the clutch side of the neck and through the electrical
caddy to the seat area.
Allen 3/16"
Tools Needed: 10mm
wrench or socket
Torx T-30
Allen 9/64"
Phillips head screw driver
Torx T-40
11/32" wrench or socket
Torx T-25
(1) Mylar cover
(1) Dummy Plug
Produktspecifikationer
| Varumärke: | Kicker |
| Kategori: | Inte kategoriserad |
| Modell: | 50HDR154 |
Behöver du hjälp?
Om du behöver hjälp med Kicker 50HDR154 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Kicker Manualer
14 Januari 2025
22 September 2024
22 September 2024
22 September 2024
24 Augusti 2024
16 Augusti 2024
Inte kategoriserad Manualer
- Ultimate Speed
- Lasita Maja
- Cooper Lighting
- A4 Tech
- ZAZU
- WOLF-Garten
- EOTech
- Bryton
- Gourmetmaxx
- Viking
- Oase
- AbleNet
- For_Q
- Toolland
- Ufesa
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025