Kidde P4010DCSCO-W Bruksanvisning
Kidde
Rökdetektor
P4010DCSCO-W
Läs gratis den bruksanvisning för Kidde P4010DCSCO-W (14 sidor) i kategorin Rökdetektor. Guiden har ansetts hjälpsam av 22 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 11.5 recensioner. Har du en fråga om Kidde P4010DCSCO-W eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/14
Hold for
8-9 seconds
Added Device
“Setup
complete!”
Installed Device
Press & hold the button on only ONE device
until you hear 2 beeps. Release button. You
will hear “Searching for other devices.”
This device will be the "Coordinator" of the network.
Keep this unit separated from others.
The light will pulse green and device will
sound a continuous "sonar" ping
until step 4 is completed.
2
Pick One Device
DON'T press buttons
on other devices
“Searching for
other devices.”
Coordinator
Wait until all devices have connected to network.
Once connected, each device will speak:
“Success now connected!”
The non-Coordinator devices are called "RFDs."
Once connected, the lights will
glow green.
3
Relax and Wait
4
Pick One Device
If all devices ash green and the “sonar”
ping has stopped, the devices are now
connected. Congratulations!
For best results, install the Coordinator unit
in a central location of the home.
Refer to user guide for detailed
installation instructions.
5
Setup Complete!
ON
1
Power Up All Devices
Locate the red wheel on the back of the device.
Turn the red wheel to the “ON” position
on ALLdevices using the included tool, or a
standard screwdriver.
Once powered, the light rings
will glow red.
USE ACTIVATION TOOL
OR SCREWDRIVER
Need more help
getting started?
Visit kidde.com/wirefreealarms
to view video tutorials or scan the
QR code below.
ON
PERMANENTLY
DISABLE and
DISCHARGE
alarm
Break
tab
1
Power Up New Device
SMOKE ALARM: 3 long beeps, repeating
CO ALARM: 4 quick beeps, repeating
STANDBY: Green LED blink every 60s
FAULT: Amber LED blink with chirp every 30s
LOW BATTERY: Amber LED blink every 5s, chirp every 60s
END OF UNIT LIFE: Amber LED blink every 5s, chirp twice every 30s
Push button to test weekly.
See user guide for more information
Wait until the new device has connected
to the network. Once connected, the new device
will speak: “Success now connected!”
Once connected, the light ring
will glow green.
3
Relax and Wait
“Success, now
connected!”
Section 2
Adding a Device
to an Existing Network
Section 1
Quick Start Wire-Free Network Setup
Section 2
Adding a Device to an Existing Network
Section 3
Resetting a Device
Light ring will ash green once and
then it will pulse red. You will hear the
words “Ready to connect, follow quick
start instructions.”
Device has been reset.
2
Resetting the Device
Press & hold the button on the device for
8-9 seconds until you hear 3 beeps.
Release button. You will hear the words
“Resetting wireless settings.”
1
Resetting the Device
Device Being Added
“Searching for
other devices.”
Installed Device
“Success, now
connected!”
Press & hold the button on only ONE device
until you hear 2 beeps. Release button.
“Sonar” ping will stop.
Device will announce that setup is
complete and the number of
connected devices.
Press & hold the button on the INSTALLED
device for 5 SECONDS until you hear 2 beeps.
Release button. “Sonar” ping will stop.
Device will announce that setup is
complete and the number of
connected devices.
Press & hold the button on only ONE INSTALLED
device on your network until you hear 2 beeps.
Release button. You will hear “Searching
for other devices.”
The light will pulse green and device will
sound a continuous "sonar" ping
until step 4 is completed.
Hold for
5 seconds
Hold for
5 seconds
Consult the User Guide for more detailed
instructions on product installation and use.
Section 3
Resetting Your Device
If you encounter an issue at any point
during the wire-free network setup process,
you may reset the device by following
the subsequent directions.
“Resetting
wireless
settings.”
“Ready to
connect, follow
Quick Start
instructions!”
Quick
Start Guide
Kidde Wire-Free Alarm Network Setup
Please Read All Instructions First!
Locate the red wheel on the back of the device
being added to the network. Using the activation
tool or a standard screwdriver, turn the red
wheel to the "on" position.
Once powered, the light ring
will glow red.
2
5
5
6
-
7
2
0
3
-
0
2
R
e
v
A
Coordinator
Coordinator
RFD
RFD
USE ACTIVATION TOOL
OR SCREWDRIVER
2
Pick One Installed Device
4
Pick the Installed Device
Produktspecifikationer
| Varumärke: | Kidde |
| Kategori: | Rökdetektor |
| Modell: | P4010DCSCO-W |
Behöver du hjälp?
Om du behöver hjälp med Kidde P4010DCSCO-W ställ en fråga nedan och andra användare kommer att svara dig
Rökdetektor Kidde Manualer
31 December 2025
14 December 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
Rökdetektor Manualer
- Pyrexx
- EMOS
- Hager
- Siemens
- Inovonics
- Elro
- EQ3
- Brennenstuhl
- Malmbergs
- H-Tronic
- Pentatech
- Abus
- Fito
- Lanberg
- FireAngel
Nyaste Rökdetektor Manualer
2 April 2025
26 Februari 2025
26 Februari 2025
26 Februari 2025
26 Februari 2025
24 Februari 2025
24 Februari 2025
20 Februari 2025
29 Januari 2025
31 December 2025