Kreg Concealed Hinge Jig Bruksanvisning
Kreg
Borrmaskin
Concealed Hinge Jig
Läs gratis den bruksanvisning för Kreg Concealed Hinge Jig (54 sidor) i kategorin Borrmaskin. Guiden har ansetts hjälpsam av 12 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 6.5 recensioner. Har du en fråga om Kreg Concealed Hinge Jig eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/54
ITEM No. KHI-PULL-INT
NK9068
Version 1 - 12/2016
Concealed Hinge Jig
Owner’s Manual | Benutzerhandbuch | Guide d’utilisation |
Manual del propietario | Brugervejledning | Omistajan käyttöopas |
Manuale di istruzioni | Gebruikershandleiding |
Brukerveiledning|Instrukcjaużytkownika|ManualdoUtilizador|
Руководствопользователя|Ägarhandbok
Safety
1
Follow your drill manufacturer’s instructions and safety guidelines.
Always wear eye protection.
The drill bit is sharp. Keep the cap on the bit until you are ready to drill. Wear gloves when handling an
unprotected bit.
Use two clamps to secure the jig to the workpiece. Do not attempt to hold it in place by hand.
Keep your body and hands away from sharp bit edges and moving parts.
Keeps hands and ngers away from the back face of the workpiece when drilling.
Parts
C
A
B
D
E
Items Included:
(A) Base
(B) Drill Guide
(C) 35mm Concealed Hinge Bit
(D) Stop Collar
(E) Hex Wrench
(F) Cap
Tools Required:
Electric drill
1⁄16" [1.5mm] drill bit
Clamps
F
Assembly 2
Turn the Drill Guide counterclockwise and
remove it from the Base. Insert the 35mm
Concealed Hinge Bit into the Drill Guide and
slide the Stop Collar onto the bit shaft until it
is seated on the shaft shoulder. Tighten the
set screw with the Hex Wrench. Set the Drill
Guide/35mm Bit aside.
Consult your hinge manufacturer’s
instructions for the distance from the edge of
the door to the edge of the 35mm hinge-cup
hole. Using a at-blade screwdriver, turn the
Edge Indexers so the appropriate dimension
aligns with the line on the Base. The edge-
of-door to edge-of-hole dimension usually is
given in millimetres. For a dimension given as
a fraction of an inch, see the cross-reference
table directional.
Stop Collar
Edge indexer
WARNING The drill bit is sharp. Keep the cap on
the bit until you are ready to drill. Wear gloves when
handling an unprotected bit.
!
ATTENTION The drill bit included with this jig is
a custom length with a shoulder for accurately
positioning the Stop Collar. Use only a Kreg 35mm
Concealed Hinge Bit as a replacement.
!
Dimension given
as fraction of an inch
Set Edge Indexers
to millimetre
dimension
1/8" 3mm
5/32" 4mm
3/16" 5mm
1/4" 6mm
Shaft shoulder
Produktspecifikationer
| Varumärke: | Kreg |
| Kategori: | Borrmaskin |
| Modell: | Concealed Hinge Jig |
Behöver du hjälp?
Om du behöver hjälp med Kreg Concealed Hinge Jig ställ en fråga nedan och andra användare kommer att svara dig
Borrmaskin Kreg Manualer
5 September 2024
2 September 2024
30 Augusti 2024
26 Augusti 2024
25 Augusti 2024
Borrmaskin Manualer
- Powerfix
- Fein
- King Craft
- Dedra
- RUKO
- Hyundai
- MSW
- Powerplus
- Metabo
- Toolcraft
- Scheppach
- Sparky
- Spit
- Hilti
- Netter Vibration
Nyaste Borrmaskin Manualer
13 Juni 2025
13 Juni 2025
13 Juni 2025
12 Juni 2025
7 Juni 2025
7 Juni 2025
3 Juni 2025
2 April 2025
2 April 2025
2 April 2025