Lancom GE PoE+ Injector Bruksanvisning

Lancom Nätverkskort/adapter GE PoE+ Injector

Läs gratis den bruksanvisning för Lancom GE PoE+ Injector (1 sidor) i kategorin Nätverkskort/adapter. Guiden har ansetts hjälpsam av 21 personer och har ett genomsnittsbetyg på 5.0 stjärnor baserat på 11 recensioner. Har du en fråga om Lancom GE PoE+ Injector eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/1

LANCOM GE PoE+ Injector

Installation . . . c o n n e c t i n g y o u r b u s i n e s s

The LANCOM GE PoE+ Injector operates as a compact 1 port PoE+ injector ccompliant

to the PoE standards IEEE 802.3at and 802.3af. It supports gigabit connections and is

ideally suited for power supply of PoE+ devices via CAT5 Ethernet cable (or better) for

distances up to 100 m. Further technical details can be found in the datasheets at

www.lancom.eu.

CWhen feeding power to PoE+ devices in outdoor applications it may be

necessary to install lightning or surge protecting equipment. Further informa-

tion on lightning protection can be found in the LANCOM Outdoor Wireless

Guide, which can be downloaded from www.lancom.eu.

Connectors and LEDs of the LANCOM GE PoE+ Injector

On one side of the LANCOM GE PoE+ Injector you will find the connection interface for

the included IEC power cord. The other side of the injector offers two RJ45 sockets for

LAN cable connection and two LEDs for status display.

ALED Indicator for LAN Connectivity and Power Supply

BEthernet socket for conneting the PoE+ device

CEthernet socket for connecting to the LAN

Mounting and connecting

AOptionally the LANCOM GE PoE+ Injector can be wall mounted using the holders

CDo not cover the housing of the LANCOM GE PoE+ Injectors and provide

sufficient air flow to avoid overheating of the device.

BConnect the LANCOM GE PoE+ Injector to an appropriate AC outlet (100 to

240 V AC) using the included power cord.

CConnect the Data In port of the PoE+ injector to a free switch port using a CAT5

Ethernet cable (or better).

DConnect the Data & Power Out port of the PoE+ injector to the PoE+ device using

a CAT5 Ethernet cable (or better).

DDo not use a cross over cable for connection between PoE+ injector and PoE+

device. Cross over cables use an improper pin assignment.

IPlease observe that the maximum distance between PoE+ injector and PoE+

device does not exceed 100 m. The PoE+ injector is not a repeater and cannot

amplify the data signal.

According to the WEEE directive (Waste Electrical and Electronic

Equipment) this device may not be disposed in your general hou-

sehold waste. Dispose the product to an appropriate collection sys-

tem for further recycling.

Troubleshooting

yellow permanently

Power supply active.

green permanently

PoE+ device is connected and fed with power.

green blinking Overload or short circuit in power supply.

DATA WER & PO

OUT

DATA

PORT

PoE+ injector

does not power

up.

Verify the connection to the AC outlet and the power cord.

Verify that the voltage at the power inlet is between 100 and

240 VAC.

Remove and re-apply power to the device. Check the indicators

during the up sequence.

The LAN LED is

not lit and the

PoE+ device

does not ope-

rate.

The injector did not detect a PoE+ device and therefore the port

is not enabled.

Verify that the connected device is designed for PoE+ opera-

tion.

Verify that you are using a standard CAT5 Ethernet cable (or

better) for the connection between PoE+ injector and PoE+

device. Do not use cross over cables!

If an external power splitter is in use, replace it with a known

verified splitter.

Ensure that the Ethernet cable is connected to the Data-In port.

Verify that the PoE+ device is connected to the Data & Power

Out port.

Try to reconnect the PoE+ device using a different PoE+ injector

to locate the error.

Verify that there is no short circuit over one of the Ethernet

cables.

The PoE+ device

operates, but

there is no data

link.

Verify that the LAN LED is lit permanently.

If an external power splitter is in use, replace it with a known

verified splitter.

Verify that you are using a standard CAT5 Ethernet cable (or

better) for the connection between PoE+ injector and PoE+

device. Do not use cross over cables!

Verify that the Ethernet cable length from the PoE+ injector to

the PoE+ device does not exceed 100 m.

Try to reconnect the PoE+ device using a different PoE+ injector

to locate the error.

LANCOM Systems GmbH I Adenauerstr. 20/B2 I 52146 Wuerselen I Deutschland I E-Mail info@lancom.de I Internet www.lancom.eu

www.lancom.eu

LANCOM, LANCOM Systems and LCOS are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners.

Subject to change without notice. No liability for technical errors and/or omissions.