Liftmaster 885LM Bruksanvisning
Liftmaster
ej kategoriserat
885LM
Läs gratis den bruksanvisning för Liftmaster 885LM (4 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 4 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 2.5 recensioner. Har du en fråga om Liftmaster 885LM eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
To prevent possible SERIOUS INJURY or DEATH from a moving gate
or garage door:
• Install door control within sight of garage door, out of reach of
children at a minimum height of 5 feet (1.5 m), and away from ALL
moving parts of door.
• NEVER permit children to operate or play with door control push
buttons or remote control transmitters.
• Activate door ONLY when it can be seen clearly, is properly adjusted
and there are no obstructions to door travel.
• ALWAYS keep garage door in sight until completely closed. NEVER
permit anyone to cross path of closing garage door.
SECURITY+ 2.0™ WIRELESS CONTROL PANEL
MODEL 885LM
GARAGE DOOR OPENER
“LEARN” BUTTON
PREMIUM MOTION DETECTING
OR MULTI-FUNCTION
CONTROL PANEL
"Learn" Button
SMART CONTROL PANEL
®
Navigation Buttons
Light Button
L
IGHT
Push Bar
Yellow "Learn" Button
INTRODUCTION
For use with Security+ 2.0™ garage door openers that have a yellow
“Learn” button. The wireless control panel can be used to as a secondary
device to open and close your garage door, and to turn on and off your
garage door opener lights.
FEATURES
PUSH BAR
Press the push bar to open and close the garage door. When the push
bar is pressed, the LED behind the push bar will blink when transmitting
a signal. To conserve battery power, the LED will turn off when not in
use. If the LED does not light when the push bar is pressed, the battery
power is low. Replace the battery.
LIGHT BUTTON
Press the Light button to turn the garage door opener lights on or off.
When the lights are turned on they will stay on until the Light button is
pressed again, or until the garage door opener is activated. Once the
garage door opener is activated the lights will turn off after the specified
period of time (the factory setting is 4-1/2 minutes). The Light button will
not control the lights when the door is in motion.
PROGRAMMING THE WIRELESS CONTROL PANEL
Choose an option below to program the wireless door control.
Option A
If programming with a Garage Door Opener “Learn” Button
1. Press and release the “Learn” button on the garage door opener.
2. Within 30 seconds, press and hold the push bar on the wireless
control panel.
3. Release the button when the garage door opener light blinks. If light
bulbs are not installed, two clicks will be heard. Proceed to Test.
Option B
If programming with a Premium Motion Detecting or Multi-Function
Control Panel
1. Press and release the “Learn” button. The command LED will blink.
2. Press and release the “Learn” button again. The command LED blinks
again.
3. Within 30 seconds, press and hold the push bar on the wireless
control panel.
4. Release the button after the garage door opener lights blink or two
clicks are heard. Proceed to Test.
Option C
If programming with a Smart Control Panel
®
Using the navigation button:
1. Press the navigation button below "MENU" and proceed to
“PROGRAM”.
2. Select “REMOTE” then press
to continue.
3. Within 30 seconds, press and hold the push bar on the wireless
control panel.
4. Release the button after the garage door opener lights blink or two
clicks are heard. Proceed to Test.
TEST THE WIRELESS CONTROL PANEL
To test, press the push bar on the wireless control panel. The garage
door will open or close. Next, press the light button on the wireless
control panel. The garage door opener lights should turn on or off. If not
repeat the programming steps.
NOTE: The wireless control panel will continue to activate the garage door
opener if a wired control panel has been placed into Lock mode.
WARNING: This product can expose you to chemicals including
lead, which are known to the State of California to cause cancer or
birth defects or other reproductive harm. For more information go
to www.P65Warnings.ca.gov
TO ERASE ALL CODES FROM GARAGE DOOR OPENER MEMORY
(REMOTE CONTROLS, KEYLESS ENTRIES AND WIRELESS CONTROL
PANEL)
To deactivate the accessories, first erase all codes:
Press and hold the “Learn” button on the garage door
opener until the learn indicator light goes out
(approximately 6seconds). All previous codes are now
erased. Reprogram each remote control, keyless entry or
wireless control panel you wish to use.
INSTALLATION
NOTE: Install the door control within sight of the garage door at a
minimum height of 5 feet (1.5 m) where small children cannot reach, and
away from the moving parts of the door.
1. Mark the location of the bottom mounting hole and drill a 5/32"
(4 mm) hole.
2. Install the bottom screw, allowing 1/8" (3 mm) to protrude from the
wall.
3. Position the bottom hole of the control panel over the screw and slide
down into place.
4. Lift the push bar up and mark the top hole.
5. Remove the wireless control panel from the wall and drill a 5/32"
(4 mm) hole for the top screw.
6. Position the bottom hole of the door control over the screw and slide
down into place.
7. Attach the top screw and close the push bar.
Replacement Parts
3V CR2032 Lithium battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10A20
WIRELESS CONTROL PANEL BATTERY
The lithium battery should produce power for up to
3years. To replace the battery, remove the two screws
and the circuit board from the plastic housing, as shown.
Insert new battery positive side up (+).
Dispose of old battery properly.
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V CR2032 coin batteries.
• DO NOT recharge, disassemble, heat above 212°F (100°C) or
incinerate.
1-800-528-9131
LiftMaster.com
WARRANTY
ONE YEAR LIMITED WARRANTY
LiftMaster
®
warrants to the first consumer purchaser of this product that
it is free from defect in materials and/or workmanship for a period of 1
year from the date of purchase.
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifi cations of this receiver
and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE
NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards for Home or offi ce use. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Produktspecifikationer
| Varumärke: | Liftmaster |
| Kategori: | ej kategoriserat |
| Modell: | 885LM |
Behöver du hjälp?
Om du behöver hjälp med Liftmaster 885LM ställ en fråga nedan och andra användare kommer att svara dig
ej kategoriserat Liftmaster Manualer
19 Oktober 2025
19 Oktober 2025
16 Oktober 2025
16 Oktober 2025
16 Oktober 2025
ej kategoriserat Manualer
- Mobotix
- Dotco
- Prismate
- Odisei Music
- Phanteks
- Smartwares
- Skil
- STEALTH Gaming
- Goobay
- MOOOV
- RAM Mounts
- Legrand
- Draper
- Otamatone
- Planet
Nyaste ej kategoriserat Manualer
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025
19 Oktober 2025