Livex Lighting Coronado 6109-91 Bruksanvisning
Livex Lighting
Lättnad
Coronado 6109-91
Läs gratis den bruksanvisning för Livex Lighting Coronado 6109-91 (1 sidor) i kategorin Lättnad. Guiden har ansetts hjälpsam av 8 personer och har ett genomsnittsbetyg på 3.8 stjärnor baserat på 4.5 recensioner. Har du en fråga om Livex Lighting Coronado 6109-91 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/1
ASSEMBLING & INSTALLATION INSTRUCTIONS PRODUCT# 6109
For Flush Mount Ceiling Fixtures
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
MOUNTING THE FIXTURE (Fig.1)
1. Shut off the power at the circuit breaker box. Remove old
fixture and all hardware from Junction Box.
2. Carefully unpack your new fixture and lay out all the parts
on a clear area. Take care not to lose any small parts
necessary for installation.
3. Thread the two Studs (A) about 1/4”into the pre-drilled
holes in the Mounting strap spaced the same distance apart
as the holes in the fixture body(B).
4. Attach the Mounting strap to the Junction Box with the two
Junction Box Screws as shown. The side of the Mounting
strap marked "GND" must face out.
5. While holding the column assembly towards the ceiling,
connect the electrical wires as Shown in Fig.2, making
sure that all wire nuts are secured. You may have to wrap
the connections with electrical tape. If your outlet has a
ground wire (green or bare copper), connect the fixture
ground wire to it. Otherwise connect fixture’s ground wire
directly to the Mounting strap with the green screw
provided. After wires are connected, tuck them carefully
inside the Junction Box.
6. Put fixture body (B) onto the junction box, aligning screws
on mounting strap with mounting holes in canopy and lock
it securely with the ball nuts(I).
7. Thread end of pipe nipple (D) into the hex nut(G). Raise the
pipe nipple assembly and shim into the glass(C) and through
the hole. Attach cover(E) onto the glass(C) and lock it with
the ball nut(F).
8. Install the light bulbs in accordance with the fixture’s
specifications.NOTE: DO NOT EXCEED THE
SPECIFIED WATTAGE.
9. Raise the glass(C) to the fixture body (B), then fasten the
arm's hook, aligning holes in the glass(C) and lock it with
the knob(H).
Your installation is now complete. Return power to the
junction box and test the fixture.
Fig.1
Fig.2
MIN 90℃ SUPPLY CONDUCTORS
White or
HOUSE
Black
WIRES
(Hot)
Smooth
FIXTURE
WIRES
Black or
Ribbed
WIRES
FIXTURE
Bare Copper(Ground)
FIXTURE
WIRES
Copper
(Ground)
HOUSE
(Neutral)
WIRES
White
Bare
Green or
WIRES
HOUSE
Produktspecifikationer
| Varumärke: | Livex Lighting |
| Kategori: | Lättnad |
| Modell: | Coronado 6109-91 |
Behöver du hjälp?
Om du behöver hjälp med Livex Lighting Coronado 6109-91 ställ en fråga nedan och andra användare kommer att svara dig
Lättnad Livex Lighting Manualer
5 Januari 2025
5 Januari 2025
5 Januari 2025
5 Januari 2025
5 Januari 2025
5 Januari 2025
5 Januari 2025
5 Januari 2025
5 Januari 2025
5 Januari 2025
Lättnad Manualer
- Gembird
- Lideka
- TP Link
- AFX
- Obsidian
- Quasar Science
- Govee
- Dyson
- Ecomed
- Metabo
- Ledino
- Xiaomi
- Chacon
- ColorKey
- Philips
Nyaste Lättnad Manualer
9 April 2025
9 April 2025
9 April 2025
8 April 2025
8 April 2025
8 April 2025
7 April 2025
5 April 2025
5 April 2025
5 April 2025