LUCIDA FabCore FC-3303 Bruksanvisning
LUCIDA
ej kategoriserat
FabCore FC-3303
Läs gratis den bruksanvisning för LUCIDA FabCore FC-3303 (14 sidor) i kategorin ej kategoriserat. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 4.4 stjärnor baserat på 2 recensioner. Har du en fråga om LUCIDA FabCore FC-3303 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/14
Product Information
LVT FLOORING
Installation Guide
Care & Maintenance
Warranty Information
2 | Product Information
Part 1. Installation Guide
Thank you for choosing a Lucida product. When properly installed and cared for, your new ooring
will be easy to maintain and keep its great look for years.
Please read all the instructions before you begin the installation. Improper installation will void
warranty.
WARNING!
Your old Floors may contain Asbestos!
DO NOT SAND, DRY SWEEP, DRY SCRAPE, DRILL,
SAW, BEAD-BLAST OR MECHANICALLY CHIP OR
PULVERIZE PREVIOUSLY INSTALLED EXISTING
RESILIENT FLOORING, BACKING, LINING FELT,
ASPHALTIC “CUTBACK” ADHESIVES OR OTHER
ADHESIVES, AS THESE PRODUCTS MAY CONTAIN
ASBESTOS FIBERS AND/OR CRYSTALLINE
SILICA.
• Avoid creating dust when removing
existing ooring and adhesive.
Inhalation of such dust is a cancer
and respiratory tract hazard.
Smoking by individuals exposed to
asbestos bers greatly increases
the risk of serious bodily harm.
• Unless positively certain that the
product is a non-asbestos-containing
material, you must presume it
contains asbestos. Regulations may
require that the material be tested
to determine asbestos content and
may govern the removal and disposal
of material. See current edition of
the Resilient Floor Covering Institute
(RFCI) publication Recommended Work
Practices for Removal of Resilient Floor
Coverings for detailed information
and instructions on removing all
resilient covering structures.
TOOLS REQUIRED:
Tape Measure, 100 lb. Roller, Square Ruler,
Chalk Line, Utility Knife
I. GENERAL PREPARATIONS
•
Commercial glue down LVT should be
stored, installed, and maintained in a
climate-controlled indoor location between
65° - 85°F.
•
Always check the cartons to assure the
pattern number is correct. Work from 2 to 3
cartons at a time, mixing the planks during
the installation.
•
Inspection of ooring material prior to
installation is required. Any defects should
be immediately reported to the supplier
from which the ooring was purchased
before installation. Lucida Surfaces will not
be responsible for labor costs to repair or
replace material with defects that were
apparent before or noticed at the end of an
installation.
•
Check if suboor/site conditions comply with
the specications described below. If you are
not satised, do not install, and contact your
supplier.
•
Flooring products can be damaged by
rough handling before installation. Exercise
care when handling and transporting these
products. Store, transport and handle the
ooring planks in a manner to prevent any
damage. Store cartons at, never on edge.
• Flooring products can be heavy and bulky.
Always use proper lifting techniques when
handling these products. Whenever possible,
make use of material-handling equipment
such as dollies or material carts. Never lift
more than you can safely handle.
•
Ensure that moisture tests have been
conducted and that the results do not exceed
the acceptable moisture limit for the adhesive
used.
• LVT ooring MUST be allowed to acclimate
Produktspecifikationer
| Varumärke: | LUCIDA |
| Kategori: | ej kategoriserat |
| Modell: | FabCore FC-3303 |
Behöver du hjälp?
Om du behöver hjälp med LUCIDA FabCore FC-3303 ställ en fråga nedan och andra användare kommer att svara dig
ej kategoriserat LUCIDA Manualer
9 September 2025
9 September 2025
9 September 2025
4 Augusti 2025
4 Augusti 2025
4 Augusti 2025
4 Augusti 2025
4 Augusti 2025
4 Augusti 2025
4 Augusti 2025
ej kategoriserat Manualer
- Cameo
- Matrix Audio
- Meireles
- Antelope Audio
- Gree
- Quartet
- Doktorvolt
- Sage
- Ermenrich
- OSD Audio
- NuPrime
- Envertec
- Valeo
- Artecta
- Sennheiser
Nyaste ej kategoriserat Manualer
9 September 2025
9 September 2025
9 September 2025
9 September 2025
9 September 2025
9 September 2025
9 September 2025
9 September 2025
9 September 2025
9 September 2025