Marshall DSL20CR Bruksanvisning
Marshall
Inte kategoriserad
DSL20CR
Läs gratis den bruksanvisning för Marshall DSL20CR (7 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 4.9 stjärnor baserat på 2 recensioner. Har du en fråga om Marshall DSL20CR eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/7
DSL20CR &
DSL20HR
OWNER’S MANUAL
INTRODUCTION
COMPLIANCE STATEMENT
WARNING:
Before going any further, make sure that
your amplier is compatible with your
mains electricity supply. If you have any
doubt, please seek help from a qualied
technician – your Marshall dealer can
help you in this respect.
MAINS INPUT & FUSE:
The specic mains input voltage
rating that your amplier has been
manufactured for is indicated on the
rear panel of the amplier. Your amplier
is provided with a detachable mains
(power) lead, which should be connected
to the MAINS INPUT socket on the rear
panel of the amplier (Rear Panel Function
#16). The correct value and type of
mains fuse is specied on the rear panel
of the amplier.
NEVER attempt to bypass the fuse or t
one of the incorrect value or type.
TRANSPORTING YOUR EQUIPMENT:
Please ensure that your amplier is
switched off, unplugged from the mains
electricity supply and all removable
cables have been disconnected from
your equipment before attempting to
move it.
IMPORTANT SET UP INFORMATION:
1. When using the DSL20HR, or the
DSL20CR with an extension speaker
cabinet(s), make sure that the
speaker cabinet(s) is connected to
the correct impedance loudspeaker
jack socket(s) on the rear panel of the
amplier. See the LOUDSPEAKERS
guide in this manual for specic
information regarding impedance
matching (Rear Panel Function #22).
WARNING:
Failure to do the above may damage
your amplier. When connecting a
speaker cabinet make sure that you
use a proper speaker cable. Never use a
screened (shielded) guitar cable for this
purpose.
2. Ensure that the POWER switch is
set to the OFF position (Front Panel
Function #15).
3. Ensure the OUTPUT switch is in the
STANDBY position
(Front Panel Function #14).
4. Connect the supplied mains (power)
lead into the MAINS INPUT (Rear
Panel Function #16) rst and then
into an electricity outlet.
5. Ensure that the volume controls on
the front panel are set to zero (Front
Panel Functions #3 & #6).
6. Plug your guitar into the INPUT jack
socket (Front Panel Function #1).
7. Switch the amplier ON using the
POWER switch, wait for a few
minutes and then switch the
OUTPUT switch to either the LOW
or HIGH position.
8. Turn the front panel POWER switch
on and wait for a few minutes
before going to point 9.
9. Turn the selected channel volume
up to your preferred level and your
amplier is ready to play.
WARNING! IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
Produktspecifikationer
| Varumärke: | Marshall |
| Kategori: | Inte kategoriserad |
| Modell: | DSL20CR |
Behöver du hjälp?
Om du behöver hjälp med Marshall DSL20CR ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Marshall Manualer
1 Januari 2025
2 Augusti 2024
1 Augusti 2024
27 Juli 2024
Inte kategoriserad Manualer
- Netgear
- Besco
- EchoMaster
- Yale
- Hailo
- Proviel
- Puls Dimension
- Hunter
- Busch And Müller
- Rocketfish
- Desview
- Kendall Howard
- Panta
- Melissa
- Ravelli
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025