Mastervolt C4-RI Bruksanvisning

Mastervolt Batteriladdare C4-RI

Läs gratis den bruksanvisning för Mastervolt C4-RI (3 sidor) i kategorin Batteriladdare. Guiden har ansetts hjälpsam av 34 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 17.5 recensioner. Har du en fråga om Mastervolt C4-RI eller vill du ställa frågor till andra användare av produkten? Ställ en fråga

Ladda ner PDF

Sida 1/3

ASTER ISION MODULAR SWITCHBOARDS

HOW TO ASSEMBLE A MASTERVISION PANEL

HOW TO LABEL A BACKLIGHT DC MODULE

AC MODULE

1. Lethal voltages exist on your vessel. Make sure all shore power, onboard

generating sources and batteries are disconnected before beginning

installation of your electrical panel.

2. AC modules will have lethal voltages on the bus bars and terminals.

Additional safety enclosures as the AC protection shield (part no. 07-09-04601-2-3)

may be required in some installations.

3. Make sure all Ac modules are bonded tot the ship’s AC ground bus. When

grouping modules together to form your panel, a single ground may be used.

Use an ohm meter to verify ground to all modules.

CAUTION GENERAL

1. Verify the modules you purchased arev configured for the source voltage

aboard your vessel / mobile. Refer to the backlight specification.

2. Installation of Mastervision panels should be completed by a person with

a thorough knowledge of marine / mobile electrical systems.

3. Wiring to and from each module should be conform to the local applicable

standards and taking into consideration the safety guidelines and measures.

Mastervolt can accept no liability for damage due to the use of the panel or

due to possible errors in the manual and the results thereof.

1. For best results, use Mastervision installation parts

2. Use connector bar 07-09-07810 and connector block

07-09-07820 to assemble the panel.

3. The mounting bolts used are M4x25

4. Secure the bolts wit hte supplied M4 nuts and O-rings.

5. To fasten the electrical panel in its frame or bulkhead use

the the stencil as supplied to cut the panelhole.

connector bar

07-09-07810

connector block

07-09-07820

HOW TO INSTALL THE BACKLIGHTING SYSTEM:

The Mastervision panels have a two-state backlight system for label illumination.

The first state is a low intensity green light that illuminates the labels on the

panel to enable label viewing in low light conditions, any time the circuit is

switched ON or OFF. The second state is a higher intensity yellow DC LED

(or orange neon lamp for AC) to indicate when a circuit is switched ON.

Power must be fed to all modules with backlight capability. This is achieved by

linking all the modules together by their backlight connectors (see drawing).

Verify the backlight AC or DC voltage on each module.

Do not use connector blocks at the outside top or

bottom edge. This is where the complete panel

will be fastened to its frame or bulkhead.

backlight

5DC

Indicator wire to

load side of breaker

busbar

for 5 breakers

To place the labels on the backlight module

remove the mounting bolts and turn the module

around.

Place the label in the embossed square on the

lens. Make sure that the label is placed

correctly and the indicator led is

uncovered.

Replace the backlight module in the

original position.

Warning:

When the module is placed correctly the

indicator led is 1mm away from the

transparant front lens.

NAVIGATION

INSTRUMENTS

1mm

10/30V power supply

L phase

N neutral

connect the indicator

wire to the load side of

the breaker

10/30V power supply

10/30V DC power supply for backlight

Note:

The power supply voltages are equal on all backlight modules,

indicator voltages are depending on the type of panel.

Produktspecifikationer

Varumärke:	Mastervolt
Kategori:	Batteriladdare
Modell:	C4-RI
Vikt:	1415 g
Bredd:	305 mm
Djup:	244 mm
Höjd:	68 mm
USB-kontakttyp:	USB Type-A, USB Type-C
Ethernet LAN:	Ja
Typ av strömkälla:	ATX
Medföljande kablar:	SATA
Antal USB 2.0-portar:	4
Antal HDMI-portar:	2
Antal Ethernet LAN (RJ-45)-portar:	1
Hörlursutgångar:	5
HDMI-version:	2.1
Antal DisplayPorts:	1
Digitalt ljud, optisk utgång:	1
Stöder Windows:	Windows 10 x64, Windows 11 x64
Antal portar USB 3.2 Gen 1 (3.1 Gen 1) Typ A:	4
Processoruttag:	LGA 1700
Processorfabrikant:	Intel
Maximalt internminne:	128 GB
Antal portar USB 3.2 Gen 2 (3.1 Gen 2) Typ C:	1
Ljudutgångskanaler:	7.1 kanalen
Ethernet-gränssnittstyp:	2.5 Gigabit Ethernet, Gigabit Ethernet
Chipset moderkort:	Intel B660
DisplayPort-version:	1.4
Typ av minnesplats:	DIMM
RAID-stöd:	Ja
Minneskanal:	Dubbelkanaals
PCI Express x16 (Gen 3.x)-platser:	1
PCI Express x1 (Gen 3.x)-platser:	1
Maximalt antal hårddiskar per hölje:	4
Gränssnitt för lagringsenheter som stöds:	M.2, PCI Express 3.0, PCI Express 4.0, SATA III
Komponent för:	PC
Typer av RAID:	0, 1,5, 10
Antal SATA III-kontakter:	4
Icke-ECC:	Ja
Kompatibla processorer:	Intel Celeron, Intel Core i3, Intel Core i5, Intel Core i7, Intel Core i9, Intel Pentium Gold
Antal lagringsenheter som stöds:	7
Minnestyper som stöds:	DDR4-SDRAM
Wifi:	Nee
Harmoniserad systemkod (HS):	84733020
Typer av lagringsenheter som stöds:	HDD & SSD
Moderkort chipset familj:	Intel
Moderkorts formfaktor:	ATX
Antal minnesplatser:	4
Minnesklockhastigheter som stöds:	2133,2400,2666,2800,2933,3000,3200,3333,3400,3466,3600,3733,3866,4000,4266,4400,4600,4800,5000,5333 MHz
BIOS-minnesstorlek:	128 Mbit
COM-anslutningar:	1
Anslutning för CPU-kylare:	Ja
Anslutningar för husfläktar:	4
ATX-strömkontakt (24-stift):	Ja
Frontpanelkontakt:	Ja
USB 2.0-anslutningar:	2
Anslutning för ljudpanel på framsidan:	Ja
Obuffrat minne:	Ja
USB 3.2 Gen 1 (3.1 Gen 1) anslutningar:	1
TPM-kontakt:	Ja
Chassiintrångsanslutning:	Ja
EPS-strömkontakt (8-stift):	Ja
Rensa CMOS-bygel:	Ja
Processorsocklar som stöds:	LGA 1700
Antal M.2 (M) platser:	3
12V strömkontakt:	Ja
RGB LED anslutningsskena:	Ja
Thunderbolt-headers:	1
USB 3.2-kontakter (3.1 Gen 2):	1
PCI Express x16 (Gen 5.x)-platser:	1