MB Quart FA2-2000.1 Bruksanvisning
Läs gratis den bruksanvisning för MB Quart FA2-2000.1 (2 sidor) i kategorin mottagare. Guiden har ansetts hjälpsam av 24 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 12.5 recensioner. Har du en fråga om MB Quart FA2-2000.1 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/2
External 40A
External 100A
External 80A
External 100A
External 125A
Place terminal in a secure
position so that it won’t
accidentally contact the
negative battery post
Power cable size
and fusing
It is critical to use the proper power
and ground cable. Select the size
listed here for your amplier model.
Always use high quality copper
cable. Visit our website for multi amp
system cable recommendations.
Be sure to use the proper fuse size
for each model.
Properly route power,
speaker and RCA cables
through the vehicle.
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplier to
a secure surface. Do not mount
the amplier upside down.
Attach the chassis ground
cable to the amplier
negative terminal. It is
important to make sure this
connection is very tight.
Bare metal
Attach the main power cable
to the amplier +12V. The
cable must run directly to
the battery and be properly
fused and be very tight.
Attach the remote turn on
wire to the amplier remote
output of the source unit.
Connect the RCA cables to the
coordinating RCA input number
that will match the speaker
outputs number.
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
Re-connect the negative
battery terminal making sure it
is securely tightened.
The chassis ground connection
is critical to the performance
of the amplier. Choose a
location that is close to the
amplier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Disconnect
negative battery
terminal
Run Cables
Mount Amplier
Negative Power
Connection
Positive Power
Connection
Remote Turn-on
Connection
Signal Input
Connection
Positive Battery
Connection
Re-connect
Negative Battery
Terminal
Chassis Ground
Be prepared to disarm your vehicle’s alarm and
to enter your radio / source unit code.
Installation
Before you start
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
1
2
3
5
7
6
8
11
12
4
POWER
REM turn on (Remote wire turn on)
when using High Level Input
- DC turn on
- Signal Sense turn on
Auto-Sense
Technical Guide
Turn on Mode
9
Model Fuse Size Cable Size
4ga
FA2-400.4
FA2-900.5
FA2-1000.1
FA2-1500.1
FA2-2000.1
Using spade terminals,connect
the speaker cables to the speaker
output connectors. Follow the
diagram below that best ts your
speaker conguration.
Speaker
Connections
Stereo
Monoblock
single woofer multiple woofersMonoblock
Bridged
10
CH1 CH2
SPEAKER
SPEAKER
REM
ON
DC
ON
SIGNAL
ON
MODE
NOTE - If the RCA’s are plugged into the amplier and the TURN ON MODE is in the
DC ON position, the amplier will NOT turn on. Please re-read QR document above or
hire a professional installer.
Produktspecifikationer
| Varumärke: | MB Quart |
| Kategori: | mottagare |
| Modell: | FA2-2000.1 |
Behöver du hjälp?
Om du behöver hjälp med MB Quart FA2-2000.1 ställ en fråga nedan och andra användare kommer att svara dig
mottagare MB Quart Manualer
13 Oktober 2025
13 Oktober 2025
13 Oktober 2025
13 Oktober 2025
29 Mars 2025
29 Mars 2025
29 Mars 2025
29 Mars 2025
29 Mars 2025
25 September 2024
mottagare Manualer
- AVM
- Shanling
- Trust
- Sunfire
- Black Hydra
- Ibiza Sound
- Pharos
- Futaba
- Axton
- Focusrite
- Albrecht
- Bluesound
- Avalon
- Lumantek
- Amplicom
Nyaste mottagare Manualer
19 Oktober 2025
19 Oktober 2025
18 Oktober 2025
18 Oktober 2025
18 Oktober 2025
18 Oktober 2025
17 Oktober 2025
15 Oktober 2025
15 Oktober 2025
15 Oktober 2025