Mean Well DRA-40-24 Bruksanvisning
Sidor 4 Engels Inte kategoriserad
Läs bruksanvisningen för Mean Well DRA-40-24 gratis online eller ladda ner PDF:en. 12 personer har tyckt att guiden var hjälpsam. Fråga om modellen? Ställ en fråga
Installaon Manual
Type：
：
：
：：DRA DIN rail power supplySeriesDRA-40, DRA-
（
（
（
（（ ：
：
：
：： 60）
）
）
））
DRA-- INPUT: -240VAC 0.8A 50/60Hz OUTPUT: V 3.34A 401210012
DRA-- INPUT: -240VAC 0.8A 50/60Hz OUTPUT: V 1.7A 402410024
DRA-- INPUT: -240VAC 1.3A 50/60Hz OUTPUT: V 5A 601210012
DRA-- INPUT: -240V 1.3A 50/60Hz OUTPUT: V 2.5A 6024100AC24
Introducon
DRA is a DIN rail power supply series featuring adjustable output current. Users are able to set its output current to
a range of 10% - 100% of rated current via 1-10Vdc, PWM signal or resistance. Like other Mean Wells DIN series, ’
they can be mounted on a TS35 Standard DIN rail.
Installaon
（ ）1Always allow good venlaon clearances, 5mm le and right, 40mm above and 20mm below, around the unit
in use to prevent it from overheang. Also a 10-15 cm clearance must be kept when the adjacent device is a
heat source.
（ ）2The appropriate mounng orientaon for the unit is vercal, the input terminals the bottom and output on at
the top. Mounng orientaons other than that, such as upside down, horizontal, or table-top mounng, is not
allowed.
（ ）3Use copper wire only, and recommended wires are shown as below.
AWG
18
16
14
12
Rated Current of
Equipment (Amp)
7
10
15
20
Cross-secon of
Lead(mm2 )
0.8
1.3
2.1
3.3
NoteCurrent each wire carries should be de-rated to 80% of the current suggested ：
above when using 4-6 wires connected to the unit.
Make sure that all strands of each stranded wire enter the terminal connecon and the screw terminals are
securely xed to prevent poor contact. If the power supply possesses mul-output terminals, please make
sure each contact is connected to wires to prevent too much current stress on a single contact.
（ ）4Use wires that can withstand temperatures of at least 80°C, such as UL1007.
（ ）5Recommended wire strapping length m (0.197. is 5m”)
（ ）6Recommended screwdriver is3, sloed type.mm
（ ）7The recommended torque seng for terminals(TB1) is 5 kgf‐cm (4.4 Lb‐in),
terminals(TB2) is 5 5 .8 kgf‐cm (Lb‐in).
（ ）8Each unit requires 0.15mA when dimming funcon is used. Please make sure your controller is capable of
driving the units.
Produktspecifikationer
| Varumärke: | Mean Well |
| Kategori: | Inte kategoriserad |
| Modell: | DRA-40-24 |
Behöver du hjälp?
Om du behöver hjälp med Mean Well DRA-40-24 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Mean Well Manualer
Mean Well MPM-10-3.3 Bruksanvisning Mean Well HRP-100-5 Bruksanvisning Mean Well ULP-150-12 Bruksanvisning Mean Well GS06E-3P1J Bruksanvisning Mean Well NFM-20-3.3 Bruksanvisning Mean Well GST25B28-P1J Bruksanvisning Mean Well HLG-185H-12B Bruksanvisning Mean Well ELG-150-C1050A-3Y Bruksanvisning
Populära i Inte kategoriserad
Mean Well LCM-60 Bruksanvisning Mean Well GSM60B15-P1J Bruksanvisning Mean Well GSM40A07-P1J Bruksanvisning