Mean Well DRA-60-12 Bruksanvisning
Mean Well
Inte kategoriserad
DRA-60-12
Läs gratis den bruksanvisning för Mean Well DRA-60-12 (4 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 11 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 6 recensioner. Har du en fråga om Mean Well DRA-60-12 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
Installaon Manual
Type：
：
：
：：DRA DIN rail power supply Series DRA-40, DRA-
（
（
（
（（ ：
：
：
：： 60）
）
）
））
DRA- - INPUT: -240VAC 0.8A 50/60Hz OUTPUT: V 3.34A 40 12 100 12
DRA- - INPUT: -240VAC 0.8A 50/60Hz OUTPUT: V 1.7A 40 24 100 24
DRA- - INPUT: -240VAC 1.3A 50/60Hz OUTPUT: V 5A 60 12 100 12
DRA- - INPUT: -240V 1.3A 50/60Hz OUTPUT: V 2.5A 60 24 100 AC 24
Introducon
DRA is a DIN rail power supply series featuring adjustable output current. Users are able to set its output current to
a range of 10% - 100% of rated current via 1-10Vdc, PWM signal or resistance. Like other Mean Well s DIN series, ’
they can be mounted on a TS35 Standard DIN rail.
Installaon
（ ）1 Always allow good venlaon clearances, 5mm le and right, 40mm above and 20mm below, around the unit
in use to prevent it from overheang. Also a 10-15 cm clearance must be kept when the adjacent device is a
heat source.
（ ）2 The appropriate mounng orientaon for the unit is vercal, the input terminals the bottom and output on at
the top. Mounng orientaons other than that, such as upside down, horizontal, or table-top mounng, is not
allowed.
（ ）3 Use copper wire only, and recommended wires are shown as below.
AWG
18
16
14
12
Rated Current of
Equipment (Amp)
7
10
15
20
Cross-secon of
Lead(mm2 )
0.8
1.3
2.1
3.3
Note Current each wire carries should be de-rated to 80% of the current suggested ：
above when using 4-6 wires connected to the unit.
Make sure that all strands of each stranded wire enter the terminal connecon and the screw terminals are
securely xed to prevent poor contact. If the power supply possesses mul-output terminals, please make
sure each contact is connected to wires to prevent too much current stress on a single contact.
（ ）4 Use wires that can withstand temperatures of at least 80°C, such as UL1007.
（ ）5 Recommended wire strapping length m (0.197 . is 5m ”)
（ ）6 Recommended screwdriver is 3 , sloed type.mm
（ ）7 The recommended torque seng for terminals(TB1) is 5 kgf‐cm (4.4 Lb‐in),
terminals(TB2) is 5 5 .8 kgf‐cm ( Lb‐in).
（ ）8 Each unit requires 0.15mA when dimming funcon is used. Please make sure your controller is capable of
driving the units.
Produktspecifikationer
| Varumärke: | Mean Well |
| Kategori: | Inte kategoriserad |
| Modell: | DRA-60-12 |
Behöver du hjälp?
Om du behöver hjälp med Mean Well DRA-60-12 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Mean Well Manualer
8 Januari 2025
7 Januari 2025
6 Januari 2025
4 Januari 2025
4 Januari 2025
30 December 2025
12 December 2024
27 Oktober 2024
27 Oktober 2024
24 September 2024
Inte kategoriserad Manualer
- Trace Elliot
- DIO
- Eller
- Yukon
- DAP Audio
- JLab
- ACE
- Flame
- Rooboost
- Molotow
- Vermeiren
- ATAG
- Industrial Music Electronics
- The T.mix
- Dynavox
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025