Mean Well NDR-240-24 Bruksanvisning
Mean Well
Inte kategoriserad
NDR-240-24
Läs gratis den bruksanvisning för Mean Well NDR-240-24 (3 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 16 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 8.5 recensioner. Har du en fråga om Mean Well NDR-240-24 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/3
Installation Manual
Type：
：
：
：：NDR DIN rail power supply（
（
（
（（Series：
：
：
：：NDR-75, 120, 240, 480）
）
）
））
NDR-75-12 INPUT: 100-240VAC 1.6A 50/60Hz OUTPUT: 12V 6.3A
NDR-75-24 INPUT: 100-240VAC 1.6A 50/60Hz OUTPUT: 24V 3.2A
NDR-75-48 INPUT: 100-240VAC 1.6A 50/60Hz OUTPUT: 24V 1.6A
NDR-120-12 INPUT: 100-240VAC 2.6A 50/60Hz OUTPUT: 12V 10A
NDR-120-24 INPUT: 100-240VAC 2.6A 50/60Hz OUTPUT: 24V 5A
NDR-120-48 INPUT: 100-240VAC 2.6A 50/60Hz OUTPUT: 48V 2.5A
NDR-240-24 INPUT: 100-240VAC 2.8A 50/60Hz OUTPUT: 24V 10A
NDR-240-48 INPUT: 100-240VAC 2.8A 50/60Hz OUTPUT: 48V 5A
NDR-480-24 INPUT: 100-240VAC 5.3A 50/60Hz OUTPUT: 24V 20A
NDR-480-48 INPUT: 100-240VAC 5.3A 50/60Hz OUTPUT: 48V 10A
Introduction
NDR is a DIN rail power supply series with an economical price and slim design. Like other Mean Well’s DIN series,
they can be mounted on a TS35 Standard DIN rail.
Installation
（ ）1 Always allow good ventilation clearances, 5mm left and right, 40mm above and 20mm below, around the unit
in use to prevent it from overheating. Also a 10-15 cm clearance must be kept when the adjacent device is a
heat source.
（ ）2 The appropriate mounting orientation for the unit is vertical, the input terminals at the bottom and output on
the top. Mounting orientations other than that, such as upside down, horizontal, or table-top mounting, is not
allowed.
（ ）3 Use copper wire only, and recommended wires are shown as below.
AWG 18 16 14 12
Rated Current of
Equipment (Amp) 7A 10A 15A 20A
Cross-section of
Lead(mm2 ) 0.8 1.3 2.1 3.3
Note: Current each wire carries should be de-rated to 80% of the current suggested
above when using 5 or more wires connected to the unit.
Make sure that all strands of each stranded wire enter the terminal connection and the screw terminals are
securely fixed to prevent poor contact. If the power supply possesses multi-output terminals, please make
sure each contact is connected to wires to prevent too much current stress on a single contact.
（ ）4 Use wires that can withstand temperatures of at least 80°C, such as UL1007.
（ ）5 Recommended wire strapping length is 5mm (0.197”).
（ ）6 Recommended screwdriver is 3mm, slotted type.
Produktspecifikationer
| Varumärke: | Mean Well |
| Kategori: | Inte kategoriserad |
| Modell: | NDR-240-24 |
Behöver du hjälp?
Om du behöver hjälp med Mean Well NDR-240-24 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Mean Well Manualer
8 Januari 2025
7 Januari 2025
6 Januari 2025
4 Januari 2025
4 Januari 2025
30 December 2025
12 December 2024
27 Oktober 2024
27 Oktober 2024
24 September 2024
Inte kategoriserad Manualer
- ZTE
- EBS
- Lahti Pro
- Lifenaxx
- Turbosound
- Franken
- Zaor
- Zoofari
- CoolerMaster
- Worx
- AMS Neve
- Bbf
- OBSBOT
- Waltec
- Olight
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025