Megger MTB7671/2 Bruksanvisning
Läs gratis den bruksanvisning för Megger MTB7671/2 (14 sidor) i kategorin mätning. Guiden har ansetts hjälpsam av 3 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 2 recensioner. Har du en fråga om Megger MTB7671/2 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/14
M
MTB7671/2
Test box
User Guide
G Safety warnings
■ Safety Warnings and Precautions must be read and
understood before the instrument is used. They be must
observed during use.
■ Only use the MTB7671/2 when both polarity indicator
LEDs are lit.
■ The MTB7671/2 is protected by an integral RCD plug which
MUST NOT be removed from the tester.
■ The interlock protected 13 A socket should only be used with
double insulated RCD and Loop testers.
■ The instrument should not be used if any part of it is damaged.
■ Replacement fuses must be of the correct type and rating. Failure
to fit the correctly rated fuse may result in a safety hazard.
■ Only shrouded test leads should be used when measuring the
230 V a.c. mains supply
Users of this equipment and/or their employers are reminded that Health and
Safety Legislation requires them to carry out valid risk assessments of all electrical
work so as to identify potential sources of electrical danger and risk of electrical
injury such as inadvertent short circuits
CAT II - Measurement category II: Equipment connected between the
electrical outlets and the user’s equipment.
CAT III - Measurement category III: Equipment connected between the
distribution panel and the electrical outlets.
CAT IV - Measurement category IV: Equipment connected between the origin
of the low-voltage mains supply and the distribution panel.
NOTE
THE INSTRUMENT MUST ONLY BE USED BY SUITABLY
TRAINED AND COMPETENT PERSONS.
Symbols used on the instrument:
F Caution: risk of electric shock
G Caution: refer to accompanying notes
t Equipment protected throughout by Double Insulation (Class II)
c Equipment complies with relevant EU Directives
Equipment complies with ‘C tick’ requirements
Do not dispose of in the normal waste stream
Interlock cover AC out supply
Fuse Fuse
RCD and loop
test supply
socket
Continuity and
insulation test
select switch
Continuity
and insulation
connection
sockets
Supply
check
indicators
RCD and loop
test select switch
MTB7671/2
LO O P
+1 0 Ω
Produktspecifikationer
| Varumärke: | Megger |
| Kategori: | mätning |
| Modell: | MTB7671/2 |
Behöver du hjälp?
Om du behöver hjälp med Megger MTB7671/2 ställ en fråga nedan och andra användare kommer att svara dig
mätning Megger Manualer
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
2 Augusti 2025
mätning Manualer
- Steinberg
- Chauvin Arnoux
- Autel
- Megasat
- Greisinger
- PeakTech
- GW Instek
- Ermenrich
- Mitsubishi
- GlowShift
- Hager
- Basetech
- Testo
- Emko
- Teslong
Nyaste mätning Manualer
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025