Metra 70-1772 Bruksanvisning
Metra
Inte kategoriserad
70-1772
Läs nedan 📖 manual på svenska för Metra 70-1772 (2 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 11 personer och betygsatt med 4.9 stjärnor i genomsnitt av 6 användare
Sida 1/2
Receiver Wiring Adaptor
120 70-1772
Revision 02/22/17
STEP 1 -- MATCH & CONNECT WIRES
*120701772*
IMPORTANT
Before starting, compare items on your invoice with items
received. Thoroughly check packing materials. If an item
is missing, please call Crutchfield at 1-888-955-6000.
Orange/White - Illumination Red - 12 Volts Switched Power
Yellow - 12 Volts Constant Power
Blue - Power Antenna
Copyright 2017 Crutchfield Corporation
White - Left Front Speaker PositiveGray - Right Front Speaker Positive
Green - Left Rear Speaker Positive
Violet - Right Rear Speaker Positive
Gray/Black - Right Front Speaker Negative White/Black - Left Front Speaker Negative
Violet/Black - Right Rear Speaker Negative Green/Black - Left Rear Speaker Negative
Match wires below to the matching function of each wire on your receiver (refer to instructions supplied with receiver). The wire colors of your
new receiver may, or may not, match the wire colors of the adaptor. Match adaptor and receiver wires by function, disregarding color.
Your receiver illumination wire could be Orange or Orange/White. As with other wires, match this wire to the illumination wire in this harness
by function, not by color. If your receiver does not have an illumination wire, tape off the illumination wire.
Individually tape off any unused wires.
Make final wiring connections following instructions on the next page.
Connect ground wire from new receiver to chassis ground in the dash.
A.
B.
C.
D.
E.
Receiver Wiring Adaptor Connections
120 70-1772
Page 2
STEP 2 -- CONTINUED
A. Strip wires back 1/2”.
B. Twist wires together and
insert in crimp cap.
C. Squeeze middle of cap
for tight connection.
Copyright 2017 Crutchfield Corporation
STEP 3 -- APPLICATION
When ready to install the receiver, plug
the Wiring Adaptor from the new receiver
or receiver assembly into the factory
radio harness(es) in the vehicle dash.
D. Complete crimp connections
for all necessary wires.
E. Be sure to wrap any wires from
the Wiring Adaptor that are
not necessary (wires with no
match from the new receiver)
with electrical tape.
STEP 2 -- CRIMP CONNECTIONS
Tools & Parts
Required
Wire Stripper/Crimp Tool Crimp Caps
Unused Wire (tape over bare wires)
Receiver Wiring Adaptor
Generic Illustration
Generic Illustration
Produktspecifikationer
| Varumärke: | Metra |
| Kategori: | Inte kategoriserad |
| Modell: | 70-1772 |
Behöver du hjälp?
Om du behöver hjälp med Metra 70-1772 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Metra Manualer
3 April 2025
3 April 2025
3 April 2025
12 Mars 2025
24 Februari 2025
24 Februari 2025
14 Januari 2025
14 Januari 2025
2 Januari 2025
2 Januari 2025
Inte kategoriserad Manualer
- Inte kategoriserad Powersoft
- Inte kategoriserad Cuggl
- Inte kategoriserad Airlive
- Inte kategoriserad APSystems
- Inte kategoriserad AURALiC
- Inte kategoriserad Neopower
- Inte kategoriserad Accsoon
- Inte kategoriserad Cascade Audio Engineering
- Inte kategoriserad SPT
- Inte kategoriserad Dreamgear
- Inte kategoriserad Melinera
- Inte kategoriserad Yuer
- Inte kategoriserad Dynon Avionics
- Inte kategoriserad Laney
- Inte kategoriserad MXL
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025