Metra 92-3005P Bruksanvisning
Metra
Inte kategoriserad
92-3005P
Läs gratis den bruksanvisning för Metra 92-3005P (3 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 11 personer och har ett genomsnittsbetyg på 4.5 stjärnor baserat på 6 recensioner. Har du en fråga om Metra 92-3005P eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/3
IMPORTANT
Installation Kit
120 92-3005P
Before starting, compare items on your invoice with items
received. Carefully check through packaging material.
If an item is missing, please call:
Crutchfield
Parts Supplied:
Kit Frame
Support Tray
Chevrolet
Revision 09/18/03
Kit assembly instructions are on the following pages.
Page 1 of 3
®
Copyright 2003 Crutchfield Corporation
*120923005P*
Mounting Bracket
(2) Studs (2) 3/8” Nuts
(4) 1/4” Hex Screws
Trimplate
at 1-888-955-6000
FIGURE 2
Shaft Supports
Installation Kit
120 92-3005P
Chevrolet
1. Press posts on trimplate into holes on kit frame to snap
parts together and secure from the rear with hex screws
(Figure 1).
2. Use a utility knife to cut out in trimplate to shaft supports
create a DIN opening (Figure 2).
3. Push clips on into slots on rear of kit frame to support tray
secure (Figure 1).
4. Use pliers to break off all tabs on mounting bracket that are
shown as shaded (Figure 3). The tabs labeled should be “B”
the only tabs remaining.
5. Secure mounting bracket to bottom of kit frame with
studs nutsand supplied (Figure 1).
6. Remove DIN sleeve from receiver and slide into opening in
trimplate. Secure sleeve to trimplate by bending the
securing tabs (Figure 4).
7. Slide receiver into sleeve/kit assembly.
DIN Receiver Assembly
2
®
Copyright 2003 Crutchfield Corporation
FIGURE 4
Securing Tabs
DIN Sleeve
Bend tabs after sleeve
is inside assembly.
FIGURE 1 Trimplate
Kit Frame
Support Tray
Mounting Bracket
Stud
Nut
Hex Screws
FIGURE 3
Tools Required
Utility
Knife
▲
Small Flat Blade
Screwdriver
3/8” & 1/4””
Sockets
Pliers
Mounting Bracket
Break off shaded tabs
“B” Tabs
Installation Kit
120 92 -3005P
Chevrolet
Spacers
(supplied with
your order)
1. Press posts on trimplate into holes on kit frame to
snap parts together and secure from rear with hex
screws (Figure 1).
2. Push clips on into slots on rear of kit frame support tray
to secure (Figure 1).
3. Use pliers to break off tabs on mounting bracket that are
shown as shaded (Figure 2). The tabs labeled “B” should
be the only tabs remaining.
4. Secure mounting bracket to bottom of kit assembly with
studs nutsand supplied (Figure 1).
5. Choose the proper spacers (supplied with your order) to
allow receiver nosepiece to extend 1/8” to 1/4” beyond
face of trimplate (Figure 3).
6. Insert receiver shafts (with spacers in place) through
openings in trimplate. Secure receiver and faceplate
with shaftnuts supplied with receiver.
7. Attach control knobs.
1/8” -1/4”
▲
▲
Spacer
Shaft Receiver Assembly
3
FIGURE 3
Shaftnuts
®
Copyright 2003 Crutchfield Corporation
FIGURE 1
Trimplate
Kit Frame
Support Tray
Mounting Bracket
Faceplate
Control Knobs
Tools Required
▲
Deep Socket
(size depends upon receiver)
Stud
Nut
Hex Screws
1/4” & 3/8”
Sockets
Pliers
FIGURE 2
Mounting Bracket
Break off shaded tabs
“B” Tabs
Produktspecifikationer
| Varumärke: | Metra |
| Kategori: | Inte kategoriserad |
| Modell: | 92-3005P |
Behöver du hjälp?
Om du behöver hjälp med Metra 92-3005P ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Metra Manualer
3 April 2025
3 April 2025
3 April 2025
12 Mars 2025
24 Februari 2025
24 Februari 2025
14 Januari 2025
14 Januari 2025
2 Januari 2025
2 Januari 2025
Inte kategoriserad Manualer
- Proficare
- Guzzanti
- SwitchBot
- Glorious
- H.Koenig
- Callpod
- Vinpower Digital
- DIEZEL
- Make Noise
- HN-Power
- Yale
- Albert Heijn
- Arco
- Volcano
- DV Mark
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025