Metra Axxess AX-ADFD02 Bruksanvisning
Metra
Inte kategoriserad
Axxess AX-ADFD02
Läs gratis den bruksanvisning för Metra Axxess AX-ADFD02 (8 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 12 personer och har ett genomsnittsbetyg på 4.6 stjärnor baserat på 6.5 recensioner. Har du en fråga om Metra Axxess AX-ADFD02 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/8
AX-ADFD02
I N S TA L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 6/27/18 INSTAX-ADFD02
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
INTERFACE FEATURES
INTRODUCTION
INTERFACE COMPONENTS
TOOLS REQUIRED
• Crimping tool and connectors or solder gun,
solder, and heat shrink • Wire cutter • Zip ties
TABLE OF CONTENTS
Connections to be made ....................................... 3
Installing & programming the AX-ADFD02
AX-ADBOX1 ...........................................................4
AX-ADBOX2 ..........................................................5
Extra features .........................................................6
Ford Data Interface 2011-up*
APPLICATIONS
See inside front cover
• Provides accessory power (12-volt 10-amp)
• Maintains the retained accessory power (R.A.P.) feature
• Provides NAV outputs (parking brake, reverse, speed sense)
• Retains SYNC
• Retains the factory AUX-IN jack
• Pre-wired ASWC-1 harness (ASWC-1 sold separately)
• Designed for non-amplified models
• Retains balance and fade
• Micro “B” USB updatable
The AX-ADFD02 harness is designed for, and must be used with, the
AX-ADBOX1 or AX-ADBOX2 interface (sold separately). Please refer to the
AX-ADBOX1 or AX-ADBOX2 for the 16-pin connector with stripped leads.
• AX-ADFD02 harness
*Visit AxxessInterfaces.com for up-to-date vehicle specific applications.
2
APPLICATIONS
FORD
Escape † 2013-up
F-250/350/450/550 XL (without CD player) †
2017-up
Fiesta † 2014-up
Fiesta (with SYNC) 2011-2013
Focus 2012-2014
Transit † 2015-up
Transit Connect † 2014-up
† With AM/FM/CD radio
3
REV. 6/27/2018 INSTAX-ADFD02
CONNECTIONS TO BE MADE
From the 16-pin harness with stripped leads to the aftermarket radio (harness included with interface):
• Connect the wire to the accessory wire.Red
If installing either an ASWC-1 or AX-LCD (both sold separately), connect the (2) Note: Red
wires on the AX-ADFD02 harness as well.
• If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.
•
If the aftermarket radio has a mute wire and the vehicle is equipped with SYNC, connect the
Brown wire to it. If the mute wire is not connected, the radio will turn off when SYNC is activated
.
• Connect the wire to the right front positive speaker output.Gray
• Connect the Gray/Black wire to the right front negative speaker output.
• Connect the wire to the left front positive speaker output.White
• Connect the wire to the left front negative speaker output.White/Black
The following (3) wires are only for multimedia/navigation radios that require these wires.
• Connect the wire to the VSS/speed sense wire.Blue/Pink
• Connect the wire to the reverse wire.Green/Purple
• Connect the Light Green wire to the parking brake wire
• Tape off and disregard the following (5) wires, they will not be used in this application:
Blue/White Green Green/Black Purple Purple/Black, , , ,
From the AX-ADFD02 harness to the aftermarket radio:
• Connect the wire to the ground wire.Black
• Connect the Yellow wire to the battery wire.
• If installing either an ASWC-1 or AX-LCD (both sold separately), connect the (2) wires to Red
accessory power.
• Connect the wire to the power antenna wire.Blue
• Connect the wire to the left rear positive speaker output.Green
• Connect the wire to the left rear negative speaker output.Green/Black
• Connect the wire to the right rear positive speaker output.Purple
• Connect the wire to the right rear negative output.Purple/Black
• If the vehicle is equipped with SYNC, and desired to be retained, connect the and Red White
RCA jacks labeled “RSE/SYNC/SAT” to the audio AUX-IN jacks.
• If the vehicle is equipped without SYNC, and the AUX-IN jack is desired to be retained,
connect the and RCA jacks labeled “FROM 3.5” to the audio AUX-IN jacks.Red White
12-pin pre-wired ASWC-1 harness:
This harness is to be used along with the optional ASWC-1 (sold separately) to retain steering
wheel audio controls. If the ASWC-1 is not being used, disregard this harness. If the ASWC-1 will be
used, please refer to the ASWC-1 instructions for radio connections and programming. Disregard
the harness that comes with the ASWC-1.
DIN jack:
The DIN jack is to be used with the optional AX-LCD (sold separately) to retain SYNC information.
Continue to Installing & Programming the AX-ADFD02
Produktspecifikationer
| Varumärke: | Metra |
| Kategori: | Inte kategoriserad |
| Modell: | Axxess AX-ADFD02 |
Behöver du hjälp?
Om du behöver hjälp med Metra Axxess AX-ADFD02 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Metra Manualer
3 April 2025
3 April 2025
3 April 2025
12 Mars 2025
24 Februari 2025
24 Februari 2025
14 Januari 2025
14 Januari 2025
2 Januari 2025
2 Januari 2025
Inte kategoriserad Manualer
- Sport-Tronic
- Leen Bakker
- Parkside
- Ninebot
- Dreamgear
- Mophie
- Brigmton
- Jumbo
- Teac
- Fontiso
- SMS
- CELLFAST
- BeamZ
- AIC
- Verbos Electronics
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025