Microchip LAN7801 Bruksanvisning
Microchip
Inte kategoriserad
LAN7801
Läs gratis den bruksanvisning för Microchip LAN7801 (13 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 11 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 6 recensioner. Har du en fråga om Microchip LAN7801 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/13
2016 Microchip Technology Inc. DS00002054A-page 1
INTRODUCTION
This application note is intended to assist customers in designing a PCB using Microchip’s family of 10/100/1000 Mbps
Ethernet devices. This document provides recommendations regarding PCB layout, a critical component in maintaining
signal integrity and reducing EMI issues. The following topics are covered:
•General PCB Layout Guidelines on page 1
•USB Layout Guidelines on page 5
•Ethernet Layout Guidelines on page 5
•EMI Considerations on page 8
•ESD Considerations on page 9
•Troubleshooting Common Layout Issues on page 10
GENERAL PCB LAYOUT GUIDELINES
Power Supply Consideration
• Ensure adequate power supply ratings. Verify that all power supplies and voltage regulators can supply the
amount of current required.
• Power supply output ripple should be limited to less than 50 mV (less than 10mV for the best performance).
• Noise levels on all power and ground planes should be limited to less than 50mV.
• Ferrite beads should be rated for 4-6 times the amount of current they are expected to supply. Any derating over
temperature should also be accounted for.
Device Decoupling
• Every high-speed semiconductor device on the PCB assembly requires decoupling capacitors. One decoupling
capacitor for every power pin is necessary.
• The decoupling capacitor value is application dependent. Typical decoupling capacitor values may range from
0.001uF to 0.1uF.
• The total decoupling capacitance should be greater than the load capacitance presented to the digital output buf-
fers to prevent noise from being introduced into the supply.
• Typically, Class II dielectric capacitors are chosen for decoupling purposes. The first choice would be an X7R
dielectric ceramic capacitor for it's excellent stability and good package size versus capacitance characteristics.
The designer's second choice may be the X5R dielectric for its excellent stability. However, the X5R may be some-
what limiting in the package size versus capacitance characteristics. Low inductance is of the utmost importance
when considering decoupling capacitor characteristics.
• Each decoupling capacitor should be located as close as possible to the power pin that it is decoupling.
• All decoupling capacitor leads should be as short as possible. The best practice is directly connecting the capaci-
tors to the ground and power pin on top layer. If using vias becomes inevitable, pad-to-via connections should be
less than 10 mils in length. Trace connections should be as wide as possible to lower inductance.
• Strongly consider connecting the ground of all bypass capacitors with two vias to greatly reduce the inductance of
that connection.
AN2054
Gigabit Ethernet Design Guide
Author: Kiet Tran
Microchip Technology Inc.
Produktspecifikationer
| Varumärke: | Microchip |
| Kategori: | Inte kategoriserad |
| Modell: | LAN7801 |
Behöver du hjälp?
Om du behöver hjälp med Microchip LAN7801 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Microchip Manualer
12 Mars 2025
12 Mars 2025
6 Mars 2025
5 Mars 2025
4 Mars 2025
4 Mars 2025
2 Mars 2025
2 Mars 2025
2 Mars 2025
2 Mars 2025
Inte kategoriserad Manualer
- Arthur Martin
- Beckmann & Egle
- Besco
- Auer Signal
- Hozelock
- HammerSmith
- Echowell
- Crystal Quest
- Giardino
- Unilux
- Simplified MFG
- Café
- Powerblade
- Brockhaus HEUER
- ProForm
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025