Microchip MIC2295YML Bruksanvisning
Sidor 4 Engels Inte kategoriserad
Läs bruksanvisningen för Microchip MIC2295YML gratis online eller ladda ner PDF:en. 12 personer har tyckt att guiden var hjälpsam. Fråga om modellen? Ställ en fråga
MIC2295 MLF®Evaluation Board
1.2MHz PWM Step-Up Converter
MLF is a registered trademark of Amkor Technology, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
February 2009
M9999-020509-B
General Description
The Micrel MIC2295 is a small 1.2MHz constant
frequency PWM DC/DC step-up switching regulator.
The MIC2295 is available in either a thin SOT-23 or a
2mm x 2mm MLF®package. High power densities, in
a very small size, are achieved using its internal
34V/1.2A switch.
Requirements
The MIC2295 evaluation board requires an input
power source that is able to deliver greater than 1.2A
at 2.5V.
Precautions
The evaluation board does not have reverse polarity
protection. Applying a negative voltage to the VIN
terminal may damage the device.
The MIC2295 evaluation board is tailored for a Li-ion
range input supply voltage. The MIC2295 evaluation
board should not exceed 6.3V on the input unless the
standard input capacitor is replaced with a higher
rated input capacitor.
Getting Started
1. Connect an external supply to VIN. Apply
desired input voltage to the VIN (J1) and
ground (J2 and J5) terminals of the evaluation
board, paying careful attention to polarity and
supply voltage (2.5V≤VIN≤6.3V). An ammeter
may be placed between the input supply and
the VIN terminal to the evaluation board.
Ensure that the supply voltage is monitored at
the VIN terminal. The ammeter and/or power
lead resistance can reduce the voltage
supplied to the input. A 10uF input capacitor is
used on the evaluation board to help
compensate for long cables used in most lab
settings.
2. Connect the load to the VOUT (J4) and
ground terminals. The load can be either
passive (resistor) or active (electronic load).
An ammeter can be placed between the load
and the VOUT terminal. The default output
voltage is set to 12V. This can be adjusted by
changing the feedback resistors.
3. Enabling the MIC2295. Apply a 1.5V or
greater voltage to the enable (J3) terminal.
Ordering Information
Part Number Description
MIC2295YML EV 1.2MHz PWM Step-Up Converter
Produktspecifikationer
| Varumärke: | Microchip |
| Kategori: | Inte kategoriserad |
| Modell: | MIC2295YML |
Behöver du hjälp?
Om du behöver hjälp med Microchip MIC2295YML ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Microchip Manualer
Microchip MCP6S22 Bruksanvisning Microchip ATSAMD51G18A Bruksanvisning Microchip SY89825U Bruksanvisning Microchip EMC1813 Bruksanvisning Microchip PIC16F18446 Bruksanvisning Microchip PIC32MZ2048ECH124 Bruksanvisning Microchip MIC5375/6 Bruksanvisning Microchip dsPIC33CK256MC506 Bruksanvisning
Populära i Inte kategoriserad
Microchip SY58022U Bruksanvisning Microchip MCP9902 Bruksanvisning Microchip SY58036U Bruksanvisning