Microchip SR10 Bruksanvisning
Läs gratis den bruksanvisning för Microchip SR10 (4 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 13 personer och har ett genomsnittsbetyg på 4.3 stjärnor baserat på 7 recensioner. Har du en fråga om Microchip SR10 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/4
Supertex inc.
Supertex inc.
www.supertex.com
SR10DB1
Doc.# DSDB-SR10DB1
A040113
- DC Output +
24V
12V
6V
ADJ
HIGH EVOLTAG
Supertex SR10DB1
C
OUT
AC Input
90-275VRMS
50/60Hz
H
N
+
–
Load
R
FB1
and R
FB2
optional for output voltages other
than 6, 12, or 24V. Adjustment range is 6 - 28V.
Pre-configured for 9V. Pads for 0603 and 0805.
DC Output:
6, 12, 24V or
adjustable 6 - 28V.
Jumper-selectable full-wave
or half-wave rectification.
Both jumpers must be in the
same position, left or right.
Jumper-selectable output voltage.
Jumper must be present. When in
the ADJ position, R
FB1
and R
FB2
must be present.
Output minus is
connected to AC line
neutral when configured
for half-wave rectification.
R
FB1
R
FB2
D
2
D
1
D
4
D
3
R
BL
R
LIM
C
S
D
OUT
C
FB
One lead must always
be in this position
Socketed components.
Accomodates various capacitor sizes
IC
1
H Input N AC
Rect
Half
Full
V
OUT
Board Layout and Connection Diagram
Inductorless Switching
Power Supply Demoboard
Specications
Parameter Value
AC Input
90VAC to 275VAC
50Hz to 60Hz
Output voltage
6V, 12V, 24V ±10%
or 6-28V using divider
Output current
1
up to 50mA
No-load input power
1
as low as 20mW
Efciency
1
up to 75%
Actual board size 88mm x 28mm
Introduction:
The Supertex SR10 is an inductorless switching power sup-
ply controller intended for operation directly from a rectied
120/240VAC line. Due to the capacitor-coupled, switched
shunt topology (CCSS), it exhibits low standby power and
good efciency while employing no magnetics nor high volt-
age electrolytic capacitors.
To meet a wide variety of applications, the SR10DB1 is
highly congurable. Many components are socketed. Half or
full-wave rectication is jumper-selectable. Output voltage is
jumper-selectable to 3 xed voltages or may be set anywhere
in the range of 6 - 28V using an on-board feedback divider.
AC Input (H and N)
Connect to the AC line. The ‘H’ terminal should be connected
to the AC line hot conductor. The ‘N’ terminal should be con-
nected to the AC line neutral conductor. When congured for
half-wave rectication, the N terminal is connected to the DC
output minus (–) terminal.
DC Output (+ and –)
Connect the load to these terminals. Do not connect earth-
grounded loads or test equipment without using an isolation
transformer on the AC line.
Output voltage is jumper-selectable at 6, 12, or 24V, or it
may be set in the range of 6 - 28V using the R
FB
feedback
divider and setting the jumper to ADJ.
Notes:
1. Dependent upon conguration and degree of transient protection.
Produktspecifikationer
| Varumärke: | Microchip |
| Kategori: | Inte kategoriserad |
| Modell: | SR10 |
Behöver du hjälp?
Om du behöver hjälp med Microchip SR10 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Microchip Manualer
12 Mars 2025
12 Mars 2025
6 Mars 2025
5 Mars 2025
4 Mars 2025
4 Mars 2025
2 Mars 2025
2 Mars 2025
2 Mars 2025
2 Mars 2025
Inte kategoriserad Manualer
- Vivo
- EBS
- Metabo
- Simmons
- Crouzet
- Alfresco
- Contax
- Adobe
- Exagerate
- Goobay
- Lanberg
- IMAC
- Full Boar
- Aqua Computer
- Sonos
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025