Mitsubishi RLD-WR/1 Bruksanvisning
Mitsubishi
Inte kategoriserad
RLD-WR/1
Läs gratis den bruksanvisning för Mitsubishi RLD-WR/1 (1 sidor) i kategorin Inte kategoriserad. Guiden har ansetts hjälpsam av 19 personer och har ett genomsnittsbetyg på 3.5 stjärnor baserat på 10 recensioner. Har du en fråga om Mitsubishi RLD-WR/1 eller vill du ställa frågor till andra användare av produkten? Ställ en fråga
Sida 1/1
INSTALLATION MANUAL
Model: RLD-WR/1
Applicable model: CENTRAL CONTROL (SL4 or later)
This document is the installation manual for the relay cable (RLD-WR/1) to be used to connect the refrigerant leak detector to the central control
(SL4 or later).
Please also refer to the installation manual provided with the refrigerant leak detector.
This relay cable can be used as an audible alarming device by connecting the refrigerant leak detector to the central control. In that case, no
power is supplied to it as it is not connected to an indoor unit. Follow the installation manual provided with the refrigerant leak detector to connect
the power supply (DC18V).
1. Accessory parts
2. Settings of refrigerant leak detector
Set up the Dip SW of the refrigerant leak detector as follows.
SW2-2 ON
SW2-3 OFF
If the Dip SW is not set up, this detector cannot be used as an audible alarming device.
3. Wiring connection
Connect the R/C cable to DO2 of the central control.
●Forinstructionsonhowtoconnecttothecentralcontrol,
refer to the installation manual provided with the central control.
Connect the R/C cable to this relay cable.
Connect the connector (2P, white) of the relay cable to the terminal (CNMA) on the detector board.
Install the upper case with care not to pinch the wiring.
Place the connection section between the R/C cable and relay cable inside the detector.
4. Settings of central control
Set “OPEN/CLOSE setting of Malfunction Output (Normal)” to “OPEN”.
Set “Malfunction Output (ALL/Leakage)” to “LEAKAGE(refrigerant leakage)”.
●Forinstructionsonhowtosetupthecentralcontrol,refertotheuser'smanualofthecentralcontrol.
据付要領書
1.付属品
2.冷媒漏えい検知キットの設定
3.配線接続
4.集中コントローラの設定
CNMA connector (2P, white)
PJZ012D149
Produktspecifikationer
| Varumärke: | Mitsubishi |
| Kategori: | Inte kategoriserad |
| Modell: | RLD-WR/1 |
Behöver du hjälp?
Om du behöver hjälp med Mitsubishi RLD-WR/1 ställ en fråga nedan och andra användare kommer att svara dig
Inte kategoriserad Mitsubishi Manualer
25 Januari 2025
25 September 2024
25 September 2024
25 September 2024
24 September 2024
23 September 2024
23 September 2024
20 September 2024
20 September 2024
16 September 2024
Inte kategoriserad Manualer
- WarmlyYours
- Nvidia
- Kanto
- Squarp Instruments
- Rocketfish
- Koolatron
- Lotus
- Vimar
- Nebula
- LawnMaster
- Ygnis
- Xcellon
- Mesa Boogie
- Callpod
- Comelit
Nyaste Inte kategoriserad Manualer
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025
9 April 2025