Mtx Audio RT60-2 Bruksanvisning
Läs nedan 📖 manual på svenska för Mtx Audio RT60-2 (44 sidor) i kategorin bilradio. Denna guide var användbar för 18 personer och betygsatt med 4.6 stjärnor i genomsnitt av 9.5 användare
Sida 1/44
RT60
.
2
2-Channel Class-AB Power Amplifier
540W
MAX
Designed by MTX in the USA
www.mtxaudio.com
www.mtxaudio.eu
SPEAKER
BRIDGE
R+
+
R- L+ L-
-
GND REM +12V FUSE
POWER
LINE OUT LINE IN
HLI
+ R - G - L +
GAIN X-OVER LPFHPFR
R
LL
6V 0,1V 40Hz 400Hz
FULL
HPF LPF 40Hz 400Hz
www.mtxaudio.com - www.mtxaudio.eu
Owner’s Manual - RT60.2
Introduction
Thank you for purchasing an MTX Audio Hi-Performance amplifier. Proper installation matched with MTX speak-
ers and subwoofers provide superior sound and performance for endless hours of waking the neighbors, slam-
min' your friends or flat out stomping wanna-be players. Congrats and enjoy the ultimate audio experience with
MTX !
Specifications :
• 2-Channel Class-AB Amplier
• CEA2006 certied Power Output :
- 90 watts RMS x 2-channel at 2 ohm and THD+N ≤1%
- 60 watts RMS x 2-channel at 4 ohm and THD+N ≤1%
- 180 watts RMS x 1-channel at 4 ohm and THD+N ≤1%
• Crossover :
- High pass 12dB/oct variable from 40Hz to 400Hz
- Low pass 12dB/oct variable from 40Hz to 400Hz
• Signal-to-Noise Ratio (1 watt) : > 80dB
• THD+Noise (Distortion) (1 watt) : ≤ 1%
• Frequency Response (±1dB) : 20Hz-30000Hz
• Maximum Input Signal : 6V
• Maximum Sensitivity : 100mV
• Dimensions : 310mm x 180mm x 55mm
• High level inputs
Control Panel
Control Panel :
Gain Control (GAIN) : The gain control matches the input sensitivity of the amplier to the source unit being used.
The operating range varies from 100mv to 6V.
Adjusting the gain
1. Turn the gain control on the amplier all the way down (counter clockwise).
2. Turn up the volume control on the source unit to approximately 3⁄4 of maximum.
3. Adjust the gain control on the amplier until audible distortion occurs.
4. Adjust the gain control down until audible distortion disappears.
5. The amplier is now calibrated to the output of the source unit.
Low-Pass High-Pass X-Over Switch (X-OVER) :
In “LPF” position, the active low pass (LP) x-over is turned on
In “HPF” position, the active high pass (HP) x-over is turned on
In “FULL” position, the x-over is turned o
High Pass X-Over Frequency Control (HPF) :
Used to select the desired high-pass (HP) x-over frequency. The frequency is adjustable from 40Hz to 400Hz..
Low Pass X-Over Frequency Control (LPF) :
Used to select the desired low-pass (LP) x-over frequency. The frequency is adjustable from 40Hz to 400Hz..
RCA Inputs (LOW INPUT) : These RCA inputs are used with source units that have RCA or Line level outputs.
(Source units need a minimum level of 100mV output for proper operation of the amplier).
MTX recommends only high quality twisted pair cables (such as StreetWires) to decrease the possibility of radi-
ated noise entering the system.
RCA outputs - These RCA output jacks are for connecting multiple ampliers to 1 stereo RCA lead coming
from the source unit (daisy chaining).
PowerOn/Protection LED - The LED illuminates red when the amp is switched on. When the amps is in shortcir-
cuit or thermal protection, the LED is blinking.
Speaker level inputs (HLI) :
This input will allow the amplier to operate from source units with speaker-level outputs. Output speaker leads
from the source unit should be tied directly to the wire harness provided with the amplifier.
Note : When speaker level inputs are used, a remote turn on wire must used to switch the amplier on and o.
(+12V) Power Terminal : This is the main power input for the amplier and must be connected directly to the
positive terminal of the vehicles battery for proper operation. Use caution when installing (+12) power cable
in the vehicle. Avoid running this cable parallel with RCA cables, antennas, or other sensitive equipment due to
massive currents that can induce noise into the audio system. It is also very important to have a tight, secure con-
nection for maximum performance. MTX recommends using 10mm
2 power wire with the MTX RT60.2 amplier.
Remote Terminal (REM) : The amplier can be turned on by applying 12 volts to this terminal. Typically this volt-
age is supplied by a wire from the source unit marked “remote” or “power antenna”.
Ground Terminal (GND) : A proper ground is required for your amplier to operate at peak performance. A short
ground cable the same diameter as the power cable should be used to attach the ground terminal directly to
the chassis of the vehicle. Always remove paint, dirt or debris to expose bare metal where the ground will be
attached.
Speaker Terminals (SPEAKER) : Connect speakers to these terminals. Observe speaker polarity throughout the
system. Improper phase can result in loss of bass response and/or poor overall sound quality.
Bridge Mode : When bridging the amplier, use the right positive terminal and the left negative terminal only.
Warning : do not bridge the amplier with an impedance lower than 4 ohm.
Fuse (FUSE) : When fuse blow, replace them with the same value. Never use a higher rated fuse !
Produktspecifikationer
| Varumärke: | Mtx Audio |
| Kategori: | bilradio |
| Modell: | RT60-2 |
Behöver du hjälp?
Om du behöver hjälp med Mtx Audio RT60-2 ställ en fråga nedan och andra användare kommer att svara dig
bilradio Mtx Audio Manualer
4 September 2024
4 September 2024
4 September 2024
3 September 2024
3 September 2024
3 September 2024
2 September 2024
2 September 2024
2 September 2024
1 September 2024
bilradio Manualer
- bilradio Boss
- bilradio Volvo
- bilradio Mac Audio
- bilradio Caliber
- bilradio Ground Zero
- bilradio Hertz
- bilradio Akai
- bilradio Vieta
- bilradio Scion
- bilradio Adcom
- bilradio McIntosh
- bilradio Ultimate
- bilradio Elta
- bilradio Sony
- bilradio Mercedes-Benz
Nyaste bilradio Manualer
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
30 Maj 2025
6 April 2025
2 April 2025
2 April 2025